Zontes ZT180MN Maintenance Manual Download

Page: 43 / 55

7-LEFT CRANKCASE ASSEMBLY

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251512-028000 26.2×38×1 thrust washer

1051054-012000 ZT180MN electric start large tooth A

1250602-028000 KT26×32×21.8 needle bearing

1051354-006000 30.2×41.2×1.5 thrust washer

1251300-066093 M18×1.0 lock nut level 10 (environmental color zinc)

95±15N.m

1051354-002000 ZT180MN output sprocket nut lock piece

1050354-023000 Rubber

－

covered output sprocket subassembly

1050254-001000 ZT180MN Output chain wheel shaft sleeve

Ordinary

1050254-007000 ZT180MN output sprocket bushing (lengthened)

Lengthened

1051454-011000 22.5×2.5 fluoro rubber o

－

ring

PROCEDURE:

●

Starting gear assembly

Take out the thrust washer

⑴

, start gear

⑵

, needle bearing

⑶

, thrust washer

⑷

. Note: Start the big gear (2), 1

thrust washer at the front and back (1).

●

Output sprocket assembly

Before disassembly and assembly, use a hammer and a flat blade to knock the locking piece

⑹

flat, use a 24#

sleeve to remove the bolt

⑸

, remove the locking piece

⑹

, and pull out the output sprocket

⑺

and sprocket shaft

sleeve

⑻

. The O-ring

⑼

is installed in the groove inside the sprocket sleeve

⑻

CAUTION

：

●

After installing the nut, knock one end of the locking piece flush with one end of the nut. Prevent bolts from

falling off.

●

When installing the shaft sleeve, please check whether the two O-rings inside the shaft sleeve have fallen off.

Fig.2 LEFT CRANKCASE

ASSEMBLY

Disassemble the large starting gear and the output

sprocket

Summary of Contents for ZT180MN
























































Search results

Summary of Contents for ZT180MN

Reviews:

Related manuals for ZT180MN

Brands by name

Popular brands

Zontes ZT180MN, Maintenance Manual

Search results

Summary of Contents for ZT180MN

Reviews:

Related manuals for ZT180MN

Brands by name

Popular brands