Zontes ZT180MN Maintenance Manual Download Page 32

Page: 32 / 55

4-RIGHT CRANKCASE COVER ASSEMBLY

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251100-070093 M6×30 flange full bolt

12±1.5N.m

1050754-007000 ZT180MN clutch spring pressure plate

1050754-021000 ZT180MN clutch spring A

1050754-024000 Sliding clutch pressure plate sub

－

assembly

1050754-006000 ZT180MN clutch release lever

1050754-023000 ZT180MN sliding clutch friction plate sub

－

assembly

1251514-006000 96.5×107×2.2×1 gasket

Flat cushion

1251512-031000 96.3×107×7 thrust washer

Butterfly gasket

1051454-017000 ZT180MN clutch cushion rubber

PROCEDURE:

●

Clutch assembly

Use an 8# sleeve to remove 3 bolts (1), and take out the pressure plate (2) and 3 springs (3). Pull out the

pressure plate

⑷

, and remove the separation lever

⑸

Take out the friction plate sub-assembly

⑹

, lock washer

⑺

, thrust washer

⑻

. The edge of the lock washer

⑺

is chamfered.

CAUTION

：

●

When installing, the side of the lock washer with lettering should face outward.

●

When disassembling the bolts, loosen them one by one. Try to keep the bolts from having too much height

difference, otherwise the parts may bounce off under the action of the spring. The installation should also be

tightened one by one.

●

Check the wear of each part of the clutch, and replace the defective parts with serious wear.

●

For installation details, please refer to "ZT310 sliding clutch disassembly video".

Clutch assembly-1

Fig.1

RIGHT CRANKCASE

COVER ASSEMBLY

Summary of Contents for ZT180MN
























































Search results

Summary of Contents for ZT180MN

Reviews:

Brands by name

Popular brands

Zontes ZT180MN, Maintenance Manual

Search results

Summary of Contents for ZT180MN

Reviews:

Brands by name

Popular brands