background image

3-CYLINDER BLOCK ASSEMBLY

21

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1

4050554-001000 ZT180MN Cylinder piston subassembly

1

2

4050554-002000 ZT180MN Cylinder body assembly

1

3

1040554-001000 ZT180MN Cylinder body

1

PROCEDURE:

Cylinder piston sub-assembly

The cylinder piston sub-assembly includes a piston assembly and a cylinder block assembly.

Cylinder block assembly

The cylinder block assembly includes a cylinder block, water inlet and outlet pipe joints and O-rings.

Cylinder block

The cylinder block is just a single cylinder block.

CAUTION

Please check the status of parts before placing an order and place an order according to your own needs.

When installing the piston, make sure that the side with the "IN" mark on the piston head is not on the side of

the water inlet pipe.

The piston ring should be inserted into the cylinder correctly, and it should not come out of the ring groove.

Pistons and cylinders are divided into four groups: A, B, C, and D. The assembled piston and cylinder must be

in the same group.

Fig.4 CYLINDER BLOCK

ASSEMBLY

Description of after-sales parts

After-sale

Summary of Contents for ZT180MN
























































Reviews: