background image

28

Throttle cable clearance

Adjustment progress

(1) Loose lock nut

 ①.

(2) Turn the adjusting screw 

 to adjust the clearance lasso, within the range of 0.5~1.0mm

.

 

(3) After completion of clearance adjustment, tighten the lock nut

.

 

After  completing  the  clearance  adjusting  throttle  cable,  ensure  the  throttle  hand  turn 

automatically  back  to  the  closed  position,  do  not  make  the  engine  idle  speed  by  adjusting 
cable. It cannot appear the situation that the idling level is up when you turn the head of the 
motorcycle at the same time. 

Idling 

When

 

you

  check  the  engine  idle  speed,  it  should  be  performed  under  the  hot  condition  of  the 

engine. engine idle speed range should be between 1500 to 1700RPM.   

If  the  idle  speed  of  engine  is  beyond  the  scope  of  regulation,  please  let  the  designated 

company service units to check the motorcycle.    

Fuel evaporative pollutants control system    

The  motorcycle  has  a  control  system  which  can  prevent  fuel  evaporation  to  the  atmosphere.  It 

should be regularly (every 10000km or every 30 months) do the following. 

(1)Check whether every connection is reliable .
(2)Check each line and the activated carbon tank crack or damage, please replace the damage. 
(3)Confirm every line and activated carbon tank whether blocking, clear or replace if necessary. 

If the fuel evaporative pollutants control system need to check and maintain, we strongly 

advise you to give this work to a qualified repair units to do it. 

    The coolant/antifreeze surface level in the main water tank should be kept between the H line and L 
line at any time. If the surface level drops to below the L line, please add the coolant/antifreeze according
to the following steps:

coolant/antifreeze

1

.

Park

 

the

 

motorcycle

 

with

 

side

 

stand

.

     2

.

Open

 

the

 

cover

 

of

 

the

 

main

 

water

 

tank

add

 

proper

 

coolant/antifreeze(when the motorcycle is in 

normal condition, the coolant/antifreeze surface level can reach to H line).

In  order  to  correctly  check  the  surface  level  of  the  coolant/antifreeze

we  should  put  the 

motorcycle into the cooling engine condition.

If  the  main  water  tank  is  empty,  please  check  and  repair  the  cooling  system  immediately. 

After you finish fixing the cooling system, add some coolant/antifreezeinside. 

It  is  bad  for  health  if  you  swallow  or  absorb  the  coolant/antifreeze

Therefore,  when  you 

use it, please don't eat and drink. After every work, please clean your hands, face or any skin 

parts demonstrated. If you swallow it mistakenly, please go to the hospital immediately. If you 

absorb it mistakenly, please breathe more fresh air in the environmental in where there is full 

of fresh air. If the coolant/antifreeze

 

runs into your eyes mistakenly, please watch your eyes 

with large amount of water at once. Also, keep the liquid away from kids and pets.

Change the coolant/antifreeze

     

It is suggest that you change the coolant/antifreeze

 

completely every

 

3

 

years or 30000 kilometers.

3

.

Please

 

note

 

the

 

cover

 

of

 

auxiliary

 

radiator

  

should

 

be

 

toward

 

the

 

fuel

 

tank

.

1
2

Summary of Contents for VX 350



















































Reviews: