background image

 

 

 

Electrical Connection and Power-up 

 

   

  

 DANGER

 

DANGER 

indicates an imminently hazardous situation 

which, if not avoided, will result in death or serious injury. 

 

Note: This operation must be performed by a 
qualified technician or electrician in accordance with 
your local electrical safety code.  

 

Installation Option 1: Connect via supplied input plugs 

1.

 

Have appropriate power whips or busway tap boxes with 

receptacles that match your Z-PDS model deployed and 

tested.  

2.

 

Ensure all Z-

PDS breakers are all in the “off” or “0” position 

during installation. 

3.

 

Consider de-energizing the power input sources for both A 

and B, if possible.  Follow all applicable safety regulations. 

4.

 

Connect the input power to the Z-PDS using the supplied 

input cord plugs.  

5.

 

Safely energize the input power whips or busway tap boxes 

for the Z-PDS A & B inputs.  

6.

 

Toggle “1 / ON” 

for all circuit breakers to ensure all the LEDs 

are illuminated. If any malfunctions occur at this point 

please reference the troubleshooting section of this guide. 

Summary of Contents for Z-PDS Series





















Reviews: