background image

9. RECYCLING

In accordance with EEC Standards and our responsibility for future generations, we

are obliged to recycle all the materials we can. Therefore, please deposit all waste

material and packaging in their corresponding recycling containers and hand in the

replaced units to the nearest handler of this type of waste product.

10. ZONAIR3D

TM

 EUROPEAN WARRANTY

A) LEGAL WARRANTY

This warranty is granted notwithstanding and in addition to the rights granted to 

the consumer against the seller by Royal Legislative Decree 1 of 16 November 2007, 

approving the consolidated text of the General Defence of Consumers and Users

Act [Ley General para la Defensa de Consumidores y Usuarios], as amended by Royal

Decree-Law 7 of 27 April 2021, transposing European Union directives on competition,

prevention of money laundering, credit institutions, telecommunications, tax measures,

prevention and repair of environmental damage, posting of workers in the provision

of transnational services and consumer protection (hereinafter, “LDCU”), as well as

other complementary and implementing regulations. Therefore, all legal rights given to

the consumer by virtue of applicable regional, Spanish or European law are expressly

confirmed.

The warranty contained herein will apply only when the products are sold to 

consumers and is valid in the following countries: Austria, Belgium, Bulgaria, Croatia, 

Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, 

Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, 

Poland, Portugal, Republic of Ireland, Romania, Slovakia, Slovenia, Spain, Sweden 

and Switzerland. However, this clause shall apply notwithstanding any limitations 

and conditions that may apply to the warranty in the country in which it is exercised, 

provided the product was purchased in one of the countries referred to above.

This Zonair3D

TM

 product is under warranty for three (3) years from when it is delivered.

During that period, Zonair3D

TM

 will be liable for any non-conformity of the product with 

that set forth the agreement, in accordance with the LDCU. Consequently, during this 

period, the consumer is entitled to request the repair or replacement of the purchased 

product, except in cases in which one of the two options is objectively impossible 

or, in comparison with the other remedy, would entail disproportionate costs for the 

retailer (due to being considerably higher than the costs of the other option), which 

will be the case when this option would impose an unreasonable expense for the seller, 

taking into account: a) the value that the goods would have had if there had been no 

nonconformity; b) the materiality of the non-conformity. In the same way, it will be 

deemed disproportionate when the alternative remedy could be performed without 

major inconvenience to the consumer and the user. Furthermore, in cases in which the 

consumer cannot require that the product be repaired or replaced or when repair or 

27

AIR PRO 500-800-1200

Summary of Contents for AIR PRO 1200































Reviews: