CV-TYQ_1415_E_20180314
15
14
Hole on the
Inner Lid
Always unplug the Power Cord,
dispose all water, and allow to cool
completely before cleaning.
The Inner Lid Gasket may need to be replaced due to time and
wear. We recommend that you replace it about once a year.
HOW TO REPLACE THE INNER LID GASKET
●
Do not attempt to dry the product by turning it upside down when the bottom is wet. (Water may get inside
the body and cause it to break or rust.)
●
Do not use the following:
・
Thinner, benzene and bleach. (Doing so may cause discoloration, crack, degradation and corrosion.)
・
Polishing powder, nylon brushes, anything made with metal, eraser pads, hard nylon sponges and abrasive cleaners. (Doing so
may cause corrosion.)
・
Detergent. (Hot water may spill out, resulting in scalds or damage. Doing so may cause unwanted odor.)
●
Do not use scrub brushes for any portions other than the Filter. (Doing so may cause corrosion.)
●
When using chemically treated cloths, do not rub too hard or leave them on the product for a long time as the surfaces of the
product may be damaged by chemical reactions.
●
Do not use a dishwasher or dish dryer for cleaning or drying. (Doing so may cause the plastic parts to deform.)
●
Before storing the product for a longer period of time, dry it completely and pack in a plastic bag to prevent odors from being absorbed.
Body
/
Upper Lid
CLEANING AND MAINTENANCE
Wipe clean with a
damp well-wrung cloth.
●
Do not wash any part of the Body, Control
Panel or Water Level Gauge with water.
(May cause malfunction or rust.)
Wipe new Inner Lid Gaskets with a wet soft sponge before attaching to the Inner Lid.
To remove the Inner Lid Gasket
To attach the Inner Lid Gasket
NOTE
①
Remove the three screws, and remove the Inner Lid.
②
Remove the Inner Lid Gasket which is installed on the
Inner Lid.
After removing the Inner Lid, check the plastic part of
the Upper Lid for abnormalities.
→
If this part is discolored or if it feels rough to the touch,
replace it (there will be a fee for this).
①
Fit the Inner Lid Gasket securely to the outer
circumference as shown in the figure.
②
Place them correctly onto the Upper Lid and tighten the
screws securely.
●
Do not lose these screws.
If the Inner Lid Gasket hardens, changes shape, turns white, or otherwise
becomes worn out, hot water may leak from the gap between the Upper Lid
and Body when tilted. Steam may also leak from the gap, causing burns and
product failures, which may result in scalds. If hot water spews from the
gap or there is steam even after replacing the Inner Lid Gasket, other parts
may be in need of repair. Please contact the store where you purchased the
product.
When the Inner Lid Gasket
hardens, changes shape,
turns white, or otherwise
becomes worn out.
Please purchase
and replace with
a new one.
Wipe with a soft wet sponge.
Inner Lid
Wipe clean with a dry cloth.
Power Cord
Filter
Remove the Filter from the Inner
Container and wash with a soft brush.
Pull the Filter up to release, and press
down firmly to attach.
If you find it difficult to clean the Filter, replace
it with a new one. (see pg.17)
●
Never use the product without installing the Filter.
(The Filter prevents foreign objects from entering the water
route or Electric Pump and obstructing the flow of hot water.)
●
Red rust spots
(
Rust Stain
)
is visible on the Inner Container.
●
Milky white or gray discoloration and/or filmy objects
are found in the water.
●
Boiling is louder than usual.
●
Hot water has an odor.
(The condition of the Inner Container will vary
depending on the water quality and frequency of use.)
Especially when...
Perform the Citric Acid Cleaning
(see pg.16) periodically.
Inner Container
Inner Lid
Gasket
Inner Lid
Screws (x3)
Inner Lid Gasket
Inner Lid
Upper Lid
CAFÉ DRIP FUNCTION
1
When the CAFÉ DRIP light
turns on, Café Drip Function is
activated.
This function decreases the amount of water dispensed to 60% of the normal setting, making it suitable
for brewing café drip coffee.
Press the button
twice.
●
Be careful not to burn yourself.
●
If using a cone filter placed directly on a
cup, be careful not to let it fall inside the
cup while brewing.
●
When using a manual drip coffee cone,
dispense a cup of hot water before
brewing. (The first cup may not be hot
enough.)
●
Pressing the UNLOCK button again during
Café Drip Function will reset the product to
the normal dispensing mode.
●
When the light turns off, the Automatic
Dispense Lock will be activated.
●
If the water level is low, it may take longer
for water to begin dispensing after pressing
the DISPENSE button.
●
If the water level is low or boiling has just
completed, water may not dispense
smoothly.
NOTE
2
You can use the Café Drip
Function for about 60 seconds
while the CAFÉ DRIP light is
on.
Press the
button to dispense
hot water.
Turns on
Long beep
1
●
Each button press changes the
Information Sound.
Press the button for more
than 3 seconds during the boiling
process or Keep Warm mode.
2
Once your desired sound
(melody or beep) is heard,
the setting is completed.
The product informs you with a melody or beeps that it has finished
boiling or the timer has been set.
HOW TO CHANGE THE INFORMATION SOUND
●
Information Sound:
When
Type
Minuet
Beautiful Dreamer
×
×
×
5 long beeps
Boiling stops
Timer is set
When and what types of
Information Sounds are heard:
Press for more
than 3 seconds
Press for more
than 3 seconds
Melody
Silent
Melody
Beeping
Silent
Press for more
than 3 seconds
Beeping
(Default)
3 long beeps
Long beep
(Melody)
●
If the Silent setting is selected, a beep will
indicate the setting has completed.
●
The Information Sound will return to
Melody if the product is unplugged.