ZOJE 1900B User Manual Download Page 52

Page: 52 / 55

6 Appendix

6.1 List of Error Information

Display Error

Name Content of Error

Solution

Machine Lock

Error

The main-shaft of

sewing machine can’t

rotate due to some

problem.

Turn off power and release the

trouble

1 0 Pattern NO. Error

The prepared pattern

number is not registered

in ROM or it is set at

unreadable. The pattern

is 0.

Press RESET switch to confirm

the pattern NO. Confirm the

content in memory switch

No.201.

3 0

Needle Rod Up

Position Error

The needle rod is not at

UP position.

Turn the hand pulley to return

the needle rod to its UP

position.

4 0 Sewing

Area

Over

The sewing area is over

the limit.

Press RESET switch to confirm

the X/Y scale rate

4 3 Enlargement

Error

The sewing stitch is

below 10mm.

Press RESET switch and

confirm the pattern and X/Y

scale rate.

4 5 Pattern

Data

Error

The pattern data cannot

be adopted.

Power off and check the data

ROM

5 0 Pause

Press the RESET switch

while sewing machine

is running. The machine

pauses.

Restart or return-to-origin after

pressing RESET switch for

thread-trimming

E 2 2 0

Controller

Abnormal

The communication

with executive device is

abnormal.

Turn off the power and repower

the machine after a while.

3 0 2 Head

Tilt

Error

Head tilt detection

switch is turned ON.

The sewing machine cannot be

operated with the head tilted.

Return the sewing machine

head to its proper position

3 0 3

Connection to

Main-shaft Fail

Can’t detection the

highest point of the

sewing machine

Turn off the power, and check

the connection of the X5 plug.

3 0 5 Thread Trimmer

Knife is not at proper

Turn off the power and check

Summary of Contents for 1900B
























































Search results

Summary of Contents for 1900B

Reviews:

ZOJE 1900B, User Manual, Page: 52 / 55

Search results

Summary of Contents for 1900B

Reviews: