background image

8

© Copyright 2015 Zoeller

®

 Co. All rights reserved.

Additional Installation Notes

Electrical Data

Amps

KVA

Code

Winding

Resistance

Line-to-Line

Model

BHP

RPM

Voltage

Phase

Hertz

Full Load

In Air

Shut Off

Locked

Rotor

IX840

2

3450

200

1

60

20.0

6.6

12.1

60

H

1.0 / 1.5

EX840

2

3450

230

1

60

17.2

4.0

10.9

56

F

1.3 / 4.0

JX840

2

3450

200

3

60

12.3

3.7

7.7

54

L

1.9

FX840

2

3450

230

3

60

10.8

3.3

6.9

42

K

2.4

GX840

2

3450

460

3

60

5.5

1.6

3.5

21

K

9.7

BAX840

2

3450

575

3

60

4.5

1.0

2.5

11

F

15.3

IX842

2

3450

200

1

60

20.0

6.6

12.1

60

H

1.0 / 1.5

EX842

2

3450

230

1

60

17.2

4.0

10.9

56

F

1.3 / 4.0

JX842

2

3450

200

3

60

12.3

3.7

7.7

54

L

1.9

FX842

2

3450

230

3

60

10.8

3.3

6.9

42

K

2.4

GX842

2

3450

460

3

60

5.5

1.6

3.5

21

K

9.7

BAX842

2

3450

575

3

60

4.5

1.0

2.5

11

F

15.3

IX841

2

3450

200

1

60

20.0

6.6

12.1

60

H

1.0 / 1.5

EX841

2

3450

230

1

60

17.2

4.0

10.9

56

F

1.3 / 4.0

JX841

2

3450

200

3

60

12.3

3.7

7.7

54

L

1.9

FX841

2

3450

230

3

60

10.8

3.3

6.9

42

K

2.4

GX841

2

3450

460

3

60

5.5

1.6

3.5

21

K

9.7

BAX841

2

3450

575

3

60

4.5

1.0

2.5

11

F

15.3

  (5)   Vent gases and odors to the atmosphere through vent pipe 

per local and state codes.

  (6)   Basin 

must 

be in accordance with all applicable codes

 

  and specifications regarding Class 

I

, Division 1, Group C & 

D environments. Basin must be sized to allow a minimum  

3 minute off-time between starts.

  (7)   The tethered variable level float switches must be free and not 

hang up on pump or pit peculiarities. Float switch circuits shall 

be intrinsically safe.

 (8) 

If

 a rail system is used, it should be non-sparking. Discharge 

elbow 

must

 be firmly anchored to the bottom of basin. In 

fiberglass basin, the bottom will need to be reinforced if the 

discharge elbow is used.

  (1)   Electrical wiring and protection 

must 

be in accordance with the 

National Electrical Code per NEC articles 500 through 503 for 

installation in Class 1, Division 1, Group C & D environments, 

and any other applicable state and local electrical requirements.

  (2)   Install proper controls. (Outdoor panels in ventillated areas 

require 

NEMA 3R or 4X enclosure) Float switch connections shall be 

intrinsically safe.

  (3)   Cords must be properly sealed per NEC articles 500 through 503 

for installation in Class 

I

, Division 1, Group C & D environments, 

to prevent moisture and gases from entering the control panel. 

  (4)  

When check valve is installed

, drill a 3/16" diameter hole in 

the discharge pipe below the check valve even with the top of 

the pump. NOTE: The hole must be below the basin cover and 

cleaned periodically. Also a vent hole is drilled in the pump hous-

ing. Be sure that this hole is cleared during any servicing.

Summary of Contents for X800 Series













Reviews: