background image

2

© Copyright 2013 Zoeller Co. All rights reserved.

Manufacturer warrants, to the purchaser and subsequent owner 

during the warranty period, every new product to be free from 

defects in material and workmanship under normal use and 

service, when properly used and maintained, for a period of 

one year from date of purchase by the end user, or 18 months 

from date of original manufacture of the product, whichever 

comes first.  Parts that fail within the warranty period, one year 

from date of purchase by the end user, or 18 months from the 

date of original manufacture of the product, whichever comes 

first, that inspections determine to be defective in material or 

workmanship, will be repaired, replaced or remanufactured at 

Manufacturer's option, provided however, that by so doing we 

will not be obligated to replace an entire assembly, the entire 

mechanism or the complete unit.  No allowance will be made 

for shipping charges, damages, labor or other charges that may 

occur due to product failure, repair or replacement.

This warranty does not apply to and there shall be no warranty 

for any material or product that has been disassembled 

without prior approval of Manufacturer, subjected to misuse, 

misapplication, neglect, alteration, accident or uncontrollable act 

of nature; that has not been installed, operated or maintained 

in  accordance  with  Manufacturer's  installation  instructions; 

that has been exposed to outside substances including but 

not limited to the following:  sand, gravel, cement, mud, tar, 

hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, 

etc.), or other abrasive or corrosive substances, wash towels 

or feminine sanitary products, etc. in all pumping applications.  

The warranty set out in the paragraph above is in lieu of all 

other warranties expressed or implied; and we do not authorize 

any representative or other person to assume for us any other 

liability in connection with our products.

Contact Manufacturer at, 3649 Cane Run Road, Louisville, 

Kentucky  40211, Attention: Customer Support Department to 

obtain any needed repair or replacement of part(s) or additional 

information pertaining to our warranty.

MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR 

SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES 

OR BREACH OF EXPRESSED OR IMPLIED WARRANTY; 

AND ANY IMPLIED WARRANTY OF FITNESS FOR A 

PARTICULAR PURPOSE AND OF MERCHANTABILITY 

SHALL BE LIMITED TO THE DURATION OF THE 

EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied 

warranty, so the above limitation may not apply to you. Some 

states do not allow the exclusion or limitation of incidental or 

consequential damages, so the above limitation or exclusion 

may not apply to you.

This warranty gives you specific legal rights and you may also 

have other rights which vary from state to state.

LIMITED WARRANTY

  1.  Read all instructions before beginning installation.
  2. Be sure the installation has a minimum of 5 feet vertical 

head.

  3.  Be sure the floor is level within 1/8" for the length and width 

of the tank.

  4.  Install 2" discharge pipe seal with flange side of seal on 

inside of lid. See Figure 7.2 on page 6. (Models 100 & 102 

only)

  5.  Use soapy water to lubricate all seals to aid installation.
  6.  Install rubber coupling/union in vent line to aid disassembly. 

See Figure 7.4 on page 6.

  7. Test unit before mounting toilet. Check On/Off levels per 

step 6 of instructions.

  8.  Do not over torque toilet mounting screws.
  9.  Do not use an automatic plumbing vent device.
  10.  Obtain model number and date code, and record information 

in the space provided on the front of this manual. Refer to 

this information when calling factory.

HELPFUL HINTS FOR EASY INSTALL

  1.    DO  read  all  installation  material  with  the  pump  and  tank.                                                      
  2.  DO inspect unit for any visible damage caused by shipping. 

Contact dealer if unit appears to be damaged.              

  3.  DO clean all visible debris from the tank.   
  4.  DO always disconnect pump from power source before 

handling. DO always connect to a separately protected and 

properly grounded ground fault protected circuit. DO NOT 

ever cut, splice or damage power cord.  DO NOT carry or 

lift pump by its power cord. DO NOT use an extension cord 

with a sewage pump. 

  5.  DO install a check valve and a union in the discharge line. DO 

NOT use

 

a discharge pipe smaller than the pump discharge 

size. 

  6.  DO test pump immediately after installation to be sure that 

the system is working properly. 

  7.  DO review all applicable local and national codes and verify 

that the installation conforms to each of them.

  8.  We DO NOT recommend this product be connected to utili-

ties other than those found in a normal bathroom applica-

tion. Washing machines and dishwashers are examples of 

equipment that we Do NOT recommend. 

DO’S AND DON'T’S FOR INSTALL

Summary of Contents for QWIK JON 100













Reviews: