© Copyright 2013 Zoeller Co. All rights reserved.
QWIK JON
®
100/101/102/103 SYSTEMS
INSTALLATION INSTRUCTIONS
1.
To help reduce the risk of electrical shock
, a properly
grounded receptacle or control box of grounding type must
be installed and protected by a ground fault circuit interrupter
(GFCI) in accordance with the National Electrical Code and
applicable local codes.
Never remove ground pin from
plug.
If pump is wired direct, a GFCI must be installed in the
control box.
(SEE WARNING BELOW)
2. Make certain that the ground fault interrupter protected
receptacle or control box is within reach of the
pump’s power
supply cord.
DO NOT USE AN EXTENSION CORD
. Extension
cords that are too long or too light do not deliver sufficient
voltage to the pump motor. But more important, they could
present a safety hazard if the insulation were to become
damaged or the connection end were to fall into a damp or
wet area.
3.
Make sure the pump's electrical supply circuit is equipped
with fuses or circuit breakers of proper capacity.
A separate
branch circuit, sized according to the National Electrical Code
for the current shown on the pump name plate is recommended.
4.
TESTING FOR GROUND.
As a safety measure, each electrical
outlet should be checked for ground using an Underwriters
Laboratory Listed circuit analyzer which will indicate if the
power, neutral and ground wires are correctly connected to
your outlet. If they are not, call a qualified licensed electrician.
5.
FOR YOUR PROTECTION ALWAYS DISCONNECT PUMP
FROM ITS POWER SOURCE BEFORE HANDLING. If
pump is wired direct, de-energize the circuit at the control
box.
Grounded pumps are supplied with a 3-prong grounded
plug to help protect you against the possibility of electrical
shock.
DO NOT UNDER ANY CIRCUMSTANCES REMOVE
THE GROUND PIN.
To reduce the risk of electrical shock,
a properly grounded receptacle or control box of grounding
type must be installed and protected by a ground fault circuit
interrupter (GFCI) in accordance with national electrical code
and applicable local codes.
6.
Installation and checking of electrical circuits and hardware
should only be performed by a qualified licensed electrician.
7.
According to the state of California (Prop 65), this product
contains chemicals known to the state of California to cause
cancer and birth defects or other reproductive harm.
NOTICE TO INSTALLER: Instructions must remain with installation.
SECTION: 6.10.067
FM1469
0413
Supersedes
1209
P/N 010536
PREINSTALLATION CHECKLIST
1. Inspect all materials. Occasionally, products are damaged during shipment. If the unit is damaged, contact your dealer before
using.
Do Not
remove the test plugs from the pump.
2. Carefully read all the literature provided to familiarize yourself with specific details regarding installation and use before at
tempting
the installation. These materials should be retained for future reference.
1. Check to be sure your power source is adequate to handle
the amperage requirements of the motor as indicated on the
pump or unit I.D. tag.
2. All plumbing (discharge and vent lines) must be installed
to meet local codes.
Unit must be vented. Do not use an
automatic plumbing vent device. Toilet will not flush.
3. Maximum continuous operating temperature for models 100
and 102 must not exceed 130°F (54°C). Maximum continuous
operating temperature for model 101 must not exceed 110°F
(43°C).
1. Repair and service should be performed by an Authorized
Service Station only. (Consult factory.)
2. NOTE: Recommended for installations up to 13' (Models
100/101) and 16' (Model 102) total dynamic head. Consult
factory if installation is above 15' vertical height in 2" pipe.
Sewage Pumps WM266, WM264 and WM211 are designed
for use in Qwik Jon
®
units only. They are not designed for
use in any other application.
3. Do not use wax seal having flange that extends into tank; it
may cause clogging. If a floor is installed over the tank, use
a Zoeller designed floor flange extender seal kit (Included).
4. For installation below the original floor line, consult Factory.
Patent No. 5,038,418
MODEL NO. _____________
DATE CODE: ____________
DATE INSTALLED: _______
U P C
®
C
SEE BELOW FOR LIST OF NOTES
NOTES
NOTE: Pumps with the “UL” mark and pumps with the “US”
mark are tested to UL Standard UL778. CSA Certified pumps
are certified to CSA Standard C22.2 No.108.
REfER TO WARRANTy ON pAgE 2.
SEE BELOW FOR LIST OF WARNINGS
CAUTION
SEE BELOW FOR LIST OF CAUTIONS
Product information presented
here reflects conditions at time
of publication. Consult factory
regarding discrepancies or
inconsistencies.
MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347
SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961
(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624
visit our web site:
www.zoeller.com
®
Your Peace of Mind is Our Top Priority
®
Model 103 is not
IAPMO approved.
