background image

20

© 2021. All rights reserved.

BATTERY

This backup system requires a good quality, 12V battery in 

order to provide maximum pumping time when needed. A 

Basement Sentry brand battery is recommended. Otherwise, 

use an AGM deep-cycle 12 volt 105 amp-hour marine battery 

or larger. Wet cell batteries contain acid and precautions must 

be taken when handling.
DO NOT USE gel batteries or automotive batteries. Batteries 

with top terminals are recommended for ease of installation.
Battery box will accommodate a maximum battery size of 

13-1/2-in L x 7-in. W x 9-1/2-in H. 
NOTE: The water level in a wet cell battery should be checked 

every month. AGM batteries should not be checked.
Battery Troubleshooting:
If pump runs without AC power but moves little or no water, the 

battery may be low. 
•  Battery will recharge if green power ‘on’ light indicates 

power has been restored and the float switch is in the off 

position.

•  If immediate use is required, replace old battery with a fully 

charged battery.

•  NOTE: The pump may continue to run on a low battery 

without sufficient power to remove water. Pump will not 

stop running until battery drops below minimum voltage.

•  CAUTION: Weak batteries can be recharged but may not 

store enough energy for full service. A weak, recharged 

battery will provide reduced pumping time. If the backup 

pump is used frequently, the battery should be checked by 

a qualified battery dealer.

•  NOTE: The battery may take up to 72 hours to recharge 

after use. This will depend on the size of the battery and the 

amount the battery is discharged during use.

If the alarm sounds during the recharge cycle, reset the 

alarm. If the alarm will not reset, unplug the charger from the 

115V outlet and disconnect the black (-) negative lead from 

the battery post. Check battery and replace if necessary. 

Reconnect and refer to the battery installation section in the 

instructions.

1

Summary of Contents for BASEMENT SENTRY STBC301























Reviews: