Zoeller BASEMENT SENTRY STBC301 Manual Download Page 19

Page: 19 / 22

11. The four circle LED’s will be blue when charging

the battery. The battery LED will flash slowly. Once

charging is complete, all four circle LED’s will turn

green.

POWER

FLOAT

STATUS

BATTERY

PUMP

SILENCE

TEST

24/7 BASEMENT

PROTECTION

USB

RESET

FLOAT

PUMP

FUSE

30 AMP

FW2065 A

P L A T I N U M

1-800-584-8089

BasementSentry.com

Solid green light

when charged

Press to

silence

alarms

START-UP AND OPERATION

CARE AND MAINTENANCE

WARNING

: Always disconnect pump from power source before

handling.

At least every three months inspect and test operation:

1. Check to be sure green ‘system ready’ light is on (indicates

AC power is on and there are no alarm conditions)

2. Test for operation:

A. Unplug primary pump and controller.

Fill basin with water to the ‘on’ level of the backup pump

and allow the pump to run for several minutes.

NOTE: The alarm will sound approximately one second

after the pump starts to run.

B. Push the Silence/reset button - the alarm will shut off.

The pump will shut off after the water level is lowered

and the float drops to the ‘off’ position.

Hold the Silence/reset button for three seconds to reset

the controller and clear any alarms or indicators

C. Plug the controller and the primary pump into the 115V

outlets. The primary pump will turn on and then off when

water reaches normal level.

The pump will continue to run after the float is lowered

or until the controller senses water is being pumping.

The four circle lights will be blue. The battery light will

flash slowly after the test as it recharges the battery. The

lights will turn green once the battery is recharged.

POWER

FLOAT

STATUS

BATTERY

PUMP

SILENCE

TEST

24/7 BASEMENT

PROTECTION

USB

RESET

FLOAT

PUMP

FUSE

30 AMP

1-800-584-8089

BasementSentry.com

DC POWER

+ 15V DC 1.6A

Summary of Contents for BASEMENT SENTRY STBC301























Search results

Summary of Contents for BASEMENT SENTRY STBC301

Reviews:

Related manuals for BASEMENT SENTRY STBC301

Brands by name

Popular brands

Zoeller BASEMENT SENTRY STBC301, Manual

Search results

Summary of Contents for BASEMENT SENTRY STBC301

Reviews:

Related manuals for BASEMENT SENTRY STBC301

Brands by name

Popular brands