background image

© Copyright 2014 Zoeller

®

 Co. All rights reserved.

4

IL0413

Figure 2

To size pressure tank properly, match the 

drawdown of the tank to the capacity of the 

pump.
(*)  For manual operation, omit the pressure 

tank and pressure switch.  Wire motor direct to 

fuse box or switch per NEC.

Gate/Ball Valve 

(Normally Open)

Check Valve

Union

Line Strainer 

or Filter 

(Optional)

Street Supply

Union

Gate/Ball Valve 

(Normally Open)

Pressure 

Gauge

Check Valve

Union

Gate/Ball Valve 

(Normally Open)

Pressure Tank

Pressure 

Switch

Main Power Box

Fuse Box 

or Switch

Union

Pressure Switch

Drain

Pressure Gauge

Pressure Relief Valve

Typical Installations

Install a pressure relief valve on 

any installation where pump pressure can exceed 

the pressure tank's maximum working pressure 

or on systems where the discharge line can be 

shut off or obstructed.  Extreme over pressure can 

result in personal injury or property damage.

IL0414

Figure 3

Foot Valve 

with Strainer

Pressure Tank

Pressure 

Switch

Pressure 

Gauge

Main Power Box

Gate/Ball Valve 

(Normally Open)

Fuse Box 

or Switch

Union

Pressure Switch

Drain

Pressure Gauge

Union

Pressure Relief 

Vacuum 

Gauge

Union

Summary of Contents for 300 Series









Reviews: