background image

20

3

4

If you have a problem...

The robot does not run along the bottom of the pool properly.

There is air inside the body of the appliance. Repeat the initial immersion procedure making sure you carry
out the steps described earlier point by point. Turn the robot right over keeping it immersed so the air
trapped inside the body escapes. Press the foam pads well to push out the air.

The robot does not mount or no longer mounts the sides.

There can be 3 reasons for this :
• The filter bag is full or clogged. Simply clean it.

• Although the water looks clear, there are microscopic algae in your pool not visible to the naked eye,

which are making the sides slippery and preventing the robot from climbing. Carry out a chlorine
shock-treatment and reduce the pH slightly. Never leave the robot in the water during a chlorine
shock-treatment.

N.B. : failure to climb the sides will not have a major effect on cleaning which is primarily done over the
bottom of the pool. Since the Sweepy M3

can turn, it will still clean the whole of the bottom surface.

The robot does not move at all.

• Make sure there is electricity being supplied to the socket to which the control box is connected.

• Make sure you have :

- set the «I / O» switch to «I»,
- pressed the «start» button,

If you have selected manual mode, check that the button controlling the direction of movement is set
to forward or back and is not in the middle position.

If the problem persists, contact your retailer.

Cleaning Efficiency seems to have reduced.

Check that the foam pads have not become smooth. As a rule, it is advisable to replace the foam pads
after one season’s use.

Your safety

Your Sweepy M3

has been manufactured in compliance with the strictest standards. To get the most

of your appliance in complete safety, treat your appliance as follows:

• Only connect the control box to an earthed electrical socket fitted with a maximum 30 mA residual

current protection device.

Summary of Contents for Sweepy M3











Reviews: