background image

page 13

enGlisH

  

 

Installation and Operation Manual   

|

   Legacy™ Model LRZM Pool/Spa Heater 

such as "The Gas Safety (Installation and Use) 

Regulations" (Statutory Instrument 1998 No. 

2451).

2.  Check the gas supply to be sure that it is the same 

as the gas indicated on the heater's rating plate.

3.  If there is any doubt regarding the capacity of 

any existing service pipes or the size required 

for new service pipes then the advice of the 

gas supplier should be requested. Installation 

pipework should be fitted and tested for gas 

soundness. Zodiac recommends the gas inlet pipe 

sizes listed in Table 5.

4.  Use the figures in Table 5 to size the gas inlet 

piping from the gas meter to the heater. Check all 

local codes for compliance before installing the 

heater.

table 5.  pipe size requirements*

Distance from Gas Meter

Heater 

Size

0-15 m

15-30 m

30-60 m

mm

mm

mm

125

20

25

25

175

25

25

32

250

25

32

32

325

32

32

40

400

32

40

40

5.  Before operating the heater, test for gas sound-

ness. Do not use a naked flame. 

6.  If the gas supply pressure is less than required, 

check for undersized pipe between the meter and 

the heater, a restrictive fitting, or an undersized 

gas meter. Gas supply pressures to the heater are 

listed in Table 2.

The draft hood outlet is to be connected to an 

unobstructed vent pipe of the same diameter, terminat-

ing outside the building. The vent must terminate at 

least 0.6 m above the highest point of the roof or other 

object that is within 3.05 m of the vent termination. 

The vent pipe must have a listed vent cap which allows 

a full equivalent opening for flue products (see Figure 

4). The top of the vent cap must be at least five (5) feet 

in vertical height above the draft hood outlet.

Double wall or equivalent vent pipe is recom-

mended. 

iMportant note

: Do not use sheet metal screws at 

the snap lock joints of gas vents.

When venting multiple appliances through one 

common duct, each appliance must have its own vent 

temperature limit switch. All vent limit switches must 

be wired in series so as to prevent any appliance from 

firing in the event of a blocked vent. Refer to national 

and local installation codes for more information on 

multiple venting.

3.3.3  inspection and replacement of 

existing Vent system with new 

Components 

If the Legacy heater is being installed to replace 

an existing pool heater, it is recommended that a new 

appropriate venting system be installed with the new 

heater. However, if an existing venting system must be 

used, be sure to carefully inspect the venting system to 

ensure that it is in good condition and continues to be 

appropriate for the Legacy heater. Replace any parts 

that are not in good and serviceable condition with 

new parts before completing the pool heater installa-

tion.

section 4.  Gas Connections

4.1 

Gas supply and piping

Review the following general instructions before 

continuing the installation.

 WarninG

The Legacy Model LRZ pool and spa heaters are 

designed for use with either natural gas or LPG. 

Check the rating plate on the inner panel to be sure 

that the heater is designed to use the type of gas 

being supplied. 

do not atteMpt to ConVert 

tHis Heater For use WitH anY otHer 

tYpe oF Fuel.

 Caution

Permanent damage to the gas valve will occur if the 

following procedures are not followed.

1.  Gas piping installation must be in accordance 

with all applicable local rules and regulations 

Figure 5.  Fitting a Gas service Cock

Gas Cock

Burner Pressure

Point

Inlet Gas Pressure 

Test Port

Summary of Contents for Legacy LRZ









































Reviews: