Zmotion ZMC306X Manual Download Page 18 | Manualshive

Page: 18 / 59

background image

ZMC306X Motion Controller User Manual V1.5

Connect 422TX and 422RX of RS422 to 422TX and 422RX of the controller

correspondingly, and connect the public ends

“

EGND

”

of RS422 communication parties

together.

→

Wiring Notes:

⚫

As above, RS485 and CAN bus belong to daisy chain topology connection, and RS422

belongs to point-to-point connection (the star topology structure cannot be used).

When the use environment is ideal and there are no many nodes, the branch structure

also can be used.

⚫

Please connect a 120Ω terminal resistor in parallel

to each end of the CAN bus for

matching the circuit impedance and ensuring communication stability.

⚫

Please be sure to connect the public ends of each node on the CAN bus to prevent

the CAN chip from burning out.

⚫

Please use STP (Shielded Twisted Pair), especially in bad environments, and make

«
...
16
17
18
19
20
...
»

Summary of Contents for ZMC306X




























































Reviews:

No comments

Related manuals for ZMC306X

Brand: Samson Pages: 48

Brand: Mako Networks Pages: 15

Brand: Dantherm Pages: 96

Extra Free RZB-02

Brand: Zamel Pages: 2

Brand: Yamaha Pages: 2

Travel About Series

Brand: Kolcraft Pages: 14

Brand: Miller-Leaman Pages: 18

XP-9 88-IoT Series

Brand: ICP DAS USA Pages: 8

Brand: ICON Pages: 2

Brand: ICP DAS USA Pages: 4

Brand: Roger Pages: 21

Brand: Auber Pages: 3

Brand: Grosvenor Pages: 5

Brand: Ublox Pages: 58

FLYGT Pareo DCM 711

Brand: Xylem Pages: 56

Brand: ADEMCO Pages: 4

Brand: Daspi Pages: 16

Brand: Daikin Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands