ZKTeco SpeedFace-V5L-RFID User Manual Download Page 10

Page: 10 / 80

SpeedFace-V5L-RFID

User Manual

P a g e

| 10

1.4

Installation set-up

1.4.1

Safety Precautions

•

Keep the device away from water or dampness. Prevent water or moisture from entering the
chassis of the attendance device.

•

Do not place the device on an unstable case or desk. The device might be damaged severely in
case of a fall.

•

Ensure proper ventilation of the equipment room and keep the ventilation vents of the device
free of obstruction.

•

Make sure that the operating voltage is the same one labelled on the attendance device.

•

Do not open the chassis when the attendance device is operating or when electrical hazards are
present to avoid electrical shocks.

1.4.2

Installation site

The device must be installed in indoor and adequate clearance is reserved at the air inlet/exhaust vents for
heat dissipation.

1.4.3

Installation Tools

•

Flat-blade screwdriver

•

Phillips screwdriver: P2-150mm

1.4.4

Installation Steps

Make sure that the device is installed as per the installation instructions. If you want to open the chassis,
you should contact the agent for permission. Otherwise, you will bear any consequence resulting from
your actions.

Summary of Contents for SpeedFace-V5L-RFID











































































Search results

Summary of Contents for SpeedFace-V5L-RFID

Reviews:

Related manuals for SpeedFace-V5L-RFID

Brands by name

Popular brands

ZKTeco SpeedFace-V5L-RFID, User Manual

Search results

Summary of Contents for SpeedFace-V5L-RFID

Reviews:

Related manuals for SpeedFace-V5L-RFID

Brands by name

Popular brands