ZIROX SGM5-EL Operation Manual Download Page 6

Electrolysis Device SGM5EL                                                                                               Application 

 

2  Application fields 

One  application  field  of  electrolysis  cells  is  the  production  of  defined  gas 
atmospheres with a low oxygen concentration (approx. 1ppm O

2

 in N

2

With 

the SGM5-EL, a defined amount of oxygen can be electrolyzed into or out of 
the measuring gas (N

2

, argon). The downstream analysis cell ensures that 

the oxygen concentration is measured accurately.  

Another application field is the use for the solid electrolyte coulometry. In this 
case the e.m.f. of the analysis cell is kept constant as nominal value of an 
automatic control loop. The current at the electrolysis cell, resulting from it, 
is proportional to the oxygen exchange by the cell. With the measurement of 
I  vs.  t  the  oxygen  exchange  of  arbitrary  samples  can  be  quantitatively 
determined. 

Furthermore, it is possible to set a defined humidity in a gas mixture. Oxygen, 
for  example,  can  be  added  to  an  argon  hydrogen  mixture.  With  the 
downstream analysis cell and a special evaluation electronics the dew point 
and so the humidity can be calculated. 

Designated use 

Main fields of application 

 

Production of defined test gases e.g. for sensor tests 

 

Examination of the oxygen permeation of polymers (e.g. foils)  

 

Controlled outgassing of reactors 

 

System calibration and monitoring of TA systems (TG, DTA, TMA, DSC)  

 

Examination of the decomposition gases in thermal analysis  

The  introduction  of  explosive  gas  mixtures,  halogens  in  high  concentration, 
and sulphuric gases (e.g. SO

2

) into the SGM5-EL is not permitted.  

 

 

With the SGM5-EL 

 

     Functions 

  the oxygen concentration in a measuring gas can be maintained 

  the electrolysis current can be maintained  

  the change of the oxygen concentration caused by probe reactions 

be quantified  

  the  oxygen  output  or  uptake  of  a  probe  be  quantified  by 

interpretation of the I*t-diagram 

  technical inert gases can be adjusted at the requested purity 

 

The requirements and limit values provided in the "Technical Data" must be 
strictly observed.  

Any other use is treated as non-authorized use. 

Summary of Contents for SGM5-EL
































Reviews: