ZIPPER MASCHINEN ZI-RPE330G User Manual Download Page 24

SAFETY 

ZIPPER MASCHINEN GmbH     www.Zipper-Maschinen.at



24   

ZI-RPE330G 

 

Check the fuel line and tank regularly for leaks and cracks. Do not operate the machine if leaks in 
the fuel system are known.  

 

Store fuel only in designated and approved containers.  

14.6

 

Hazard warnings 

Despite intended use, certain residual risks remain.  

 

Squashing 

Keep your hands and feet away from moving parts, because they might get under the plate compactor. 

Wear steel-toed shoes for minimizing this danger. 
You also have to take care that the machine and the operator have a good stand. The machine mustn’t 

fall, slide or keel over during operation. 

 

Damage to health by vibrations 

Longer operations lead to circulation disorder. So: 

 

Have breaks regularly. 

 

Wear safety gloves which decrease the vibration intensity. 

 

The hardness of the working ground, cold temperatures and personal disposition decrease the 

allowed operation time. Excessive operation times may cause damages of the joints and the muscles. 

Have breaks and restrain the operation time corresponding your state of health and your physical 

welfare. 

 

Sources of danger of the working area 

Ensure that the walls of a trench are steady and that they won’t tumble down by the vibrations. 
Ensure that there are no voltage-carrying cables, gas lines or water pipes which can be damaged 

during operation. Be careful when you work near unprotected holes or excavations. The operation of 

the machine happens on your own responsibility and your discretion. 

 

Burning hazard 

Touching the muffler of the exhaust may cause serious burnings when the engine is hot. 

 

Fire and explosion hazards 

Petrol is flammable easily and at special conditions explosive. 

NEVER refill fuel during operation or when the machine is hot. 

Do not smoke and keep away flames and sparks during refilling and at places where fuel is stored. 

Do not overfill the fuel tank and avoid spilling petrol. When fuel has been spilled you must clean that 

place before starting the machine. 

Ensure that the tank cap is fastened well after refilling. 

 

Chemical dangers  

Never refill or operate a combustion engine in a closed room without enough air circulation. 

Carbon monoxide from the combustion engine can cause the death or can damage your health by 

breathing in. That’s why you’re only allowed to operate the machine in good ventilated rooms and 

outdoors. Due to the design and construction of the machine, hazardous situations may occur which 

are identified as follows in these operating instructions: 

D A N G E R

 

 

A safety instruction designed in this way indicates an imminently hazardous situation 

which, if not avoided, will result in death or serious injury.

 

W A R N I N G  

 

Such a safety instruction indicates a potentially hazardous situation which, if not 

avoided, may result in serious injury or even death. 

C A U T I O N  

 

A safety instruction designed in this way indicates a potentially hazardous situation 

which, if not avoided, may result in minor or moderate injury.

 

Summary of Contents for ZI-RPE330G









































Reviews: