background image

5.9.4

Con

guring the ZArec4C

CAUTION!

Warning!
Overheating of the brake resistor

If a wrong brake resistor is con

gured in the menu 

Basic settings/BR_TYP

, this can destroy the brake 

resistor used. 

"

Con

gure the brake resistor used in the 

Basic settings/BR_TYP

 parameter. 

Basic settings

|

-

"

BR_TYP

Off

|

-

"

BR14

BR - Type

5.9.5

Connection brake resistor

CAUTION!

Warning!
Overheating of the brake resistor

The brake resistor can burn out in case of a fault.

"

You must connect an available temperature monitor to the ZArec4C 026 and ZArec4C 039.

CAUTION!

Warning!
Overheating of the brake resistor

When connecting a brake resistor to the +DC and -DC terminals of the X2 connection terminal, this is 
directly connected to the intermediate circuit of the ZArec4C. This can destroy the brake resistor. 

"

Connect the brake resistor to the R+ and R- terminals (in the case of ZArec4C 026-039).

Information

The brake resistor of the BR14-A type has no temperature monitor.  

If a BR14-A is connected to a ZArec4C 026/039, the temperature monitor must be bridged at the X-
BC connection terminal.

BR

+DC

R

Temp. BR

X-BC

+DC

X-BR

R

(5)

(6)

(7)

ZArec4C 026/039 

Connecting BR14-A to ZArec4C 026/039

BR

TB1

TB2

+DC

R

Temp. BR

X-BC

+DC

X-BR

R

ZArec4C 026/039 

1

(5)

(6)

(7)

Connecting BR25/BR50

Original operating instructions

ZArec4C

Electrical installation

R-TBA14_03-GB 1817 Index 007

Part.-No. 00163436-GB

28/64

Summary of Contents for ZA rec 4C Series

































































Reviews: