manualshive.com logo in svg

ZIEHL-ABEGG ZA rec 4C Series, Original Operating Instructions

Share
Download
ZIEHL-ABEGG ZA rec 4C Series Original Operating Instructions Download Page 11

4.3.2

ZArec4C 026/039

The ZArec4C 026/039 is mounted on a wall or in a shaft using a fastening plate. The ZArec4C 
026/039 is to be mounted in a vertical installation position. 

"

Loosen and remove the safety screws (1).

"

Remove the ZArec4C 026/039 from the fastening plate (2). 

1

1

safety screw

1

2

1

safety screw

2

fastening plate

"

Trace the positions of the fastening points (3) of the fastening plate. See the dimension drawings in 
the chapter "Mechanical Installation/Dimensions/Minimum Clearances" for the distances between 
the fastening points.

3

3

3

3

3

Fastening points

"

Drill fastening holes.

"

Screw on the fastening plate. Use suitable fasteners for this purpose.

"

Suspend ZArec4C 026/039 on the fastening plate. 

Original operating instructions

ZArec4C

Mechanical installation

R-TBA14_03-GB 1817 Index 007

Part.-No. 00163436-GB

11/64

Summary of Contents for ZA rec 4C Series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands