Zepro ZHZ 500-850 Installation Instruction Download

Page: 58 / 82

Installation

www.zepro.com

7.9.2

Installation of main fuse on vehicles with M8 connection point (+)

When installing the main power cable, the fuse, 150A (24V) or 250 (12V), must be installed on the vehicle’s con-

nection point (+). This is to protect the electrical system from damage and risk of fire in the event of a short circuit

1. Place the fuse on the connection point and connect the main power cable, see Fig 47.

The following image showing the connection point is an example and may vary from vehicle to vehicle.

2. Secure the fuse and main power cable with the knob.

The knob must lie against and centre the cable clip so that it does not come into contact with the bolt.

Incorrect installation can cause the fuse to malfunction. Risk of fire in the event of a short circuit, see

Fig

48 and Fig 49.

WARNING!

Fig 47. Install fuse and connect main current cable

Fig 48. Correct installation

Fig 49. Incorrect installation

Summary of Contents for ZHZ 500-850



















































































Search results

Summary of Contents for ZHZ 500-850

Reviews:

Related manuals for ZHZ 500-850

Brands by name

Popular brands

Zepro ZHZ 500-850, Installation Instruction

Search results

Summary of Contents for ZHZ 500-850

Reviews:

Related manuals for ZHZ 500-850

Brands by name

Popular brands