background image

26

8. Operation

English

STARTING ENGINE

The cutting head will start rotating upon the engine
starts.

1. Rest the unit on a flat, firm place. Keep the cutting

head off the ground and clear of surrounding objects
as it will start rotating upon starting of the engine.

2. Push the primer pump several times until overflown

fuel flows out in the return tube. (OP1)

3. Move the choke lever to the closed position. (OP2)

(1) Choke lever 

(2) A: the closed position

(3) B: the open position

4. Set the ignition switch to the “start” position. (OP3)

(1) Ignition switch (2) Stop
(3) Start

5. While holding the unit firmly, pull out the starter rope

quickly until engine fires. (OP4)

• Avoid pulling the rope to its end or returning it by

releasing the knob. Such actions can cause starter
failures.

6. Move the choke lever to the open position (OP2).

And pull out the starter rope quickly to restart
engine. (OP4)

7. Allow the engine to warm up for several minutes

before starting operation.

1. When restarting the engine immediately after

stopping it, leave the choke open (OP2) and push
the primer pump several times (OP4). 

2. Overchoking can make the engine hard to start due

to excess fuel. When the engine failed to start after
several attempts, open the choke and repeat pulling
the rope, or remove the spark plug and dry it.

NOTE

IMPORTANT

WARNING

OP1

(1)

A

B

(2)

(3)

OP2

OP3

OP4

Summary of Contents for BT250





















































Reviews: