Zenno SS40E Operation Manual Download Page 6 | Manualshive

Page: 6 / 29

background image

-

6

-



Reverse side details

1.

Duplicate button

：

2.

To duplicate or cancel the remote control

3.

Mode switch

：



To switch between

USER MODE

and

SETTING MODE

。

4.

Battery cover

※

Notice:

About the remote control:



Please do not install the socket at a location that may be exposed to direct sunlight.



If the Remote Control activates other electronic appliances, please contact the distributor.

Caution:



FCC ID: YUYSSRC002



This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.



Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

2

1

3

«
...
4
5
6
7
8
...
»

Summary of Contents for SS40E






























Reviews:

No comments

Related manuals for SS40E

Brand: Kärcher Pages: 224

Brand: EBARA Pages: 36

Brand: Briggs & Stratton Pages: 144

AUTOMATE MT01-2101-069002

Brand: rollease acmeda Pages: 30

Brand: Albin Pages: 31

Brand: Yamakoyo Pages: 41

Brand: Volvo Penta Pages: 29

Brand: Volvo Penta Pages: 56

Brand: Volvo Penta Pages: 96

Brand: MerCruiser Pages: 118

Sterndrive 4.3L TKS

Brand: MerCruiser Pages: 130

Brand: MerCruiser Pages: 135

Brand: Quectel Pages: 37

Brand: Detroit Diesel Pages: 40

Brand: Hino Motors Pages: 216

Brand: Hino Pages: 278

Brand: Motion Pages: 42

Brand: Briggs & Stratton Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands