background image

 

 

 

KLIC-DA LT

 

http://www.zennio.com

 

Technical Support:

 

http://zennioenglish.zendesk.com 

 

12 

 

Additional Information (Status)

, which enables or disables the 

supervision of a set of indicators related to the power 
consumption/production and to the water flow. See section  3.1.1.6. 

Depending on the Altherma LT system being interfaced, the checkboxes of the 
required functions  need to be marked. This will make some communication objects 
visible, as described in the following sections of this user manual.  

One more parameter should be configured: 

Send Status Objects on Bus Voltage 

Recovery?

, which may be set to one of the following: 

 

No

 (default): no objects will be sent to the KNX bus during the device start-up 

after a bus power failure or a download from ETS.  

 

Yes

: the following objects will be sent to the KNX bus (to update other KNX 

devices) when the device starts up after a bus power failure  or a download 
from ETS: 

  [DHW] On/Off (Status)  

  [DHW] Booster mode On/Off (Status) 

  [DHW] Temperature (Status) 

  [DHW] Operating (Status) 

  [Climate] On/Off (Status)  

  [Climate] Operation mode (Status)  

  [Climate] Temperature (Status) 

  [Climate] Operating (Status) 

  [Temperatures] DHW tank 

  [Temperatures] Outdoor Temperature 

  [Temperatures] Leaving water 

  [Temperatures] Leaving water (PHE) 

  [Temperatures] Inlet water 

  [Temperatures] Refrigerant 

  [Actuators] Pump 

  [Actuators] Compressor 

  [Actuators] BUH: step 1 

  [Actuators] BUH: step 2 

  [Addit. Info.] Flow rate 

  [Addit. Info.] Electrical energy consumpt. 

  [Addit. Info.] Energy production 

It is possible to apply a certain delay (0 to 255 seconds) to the above sending 
once the device start-up is over. Therefore, a new parameter called 

Sending 

Delay

 will show if the above is set to “Yes”. 

Regarding the

 start-up of the device

, it is advisable to read section   2.1, as it contains 

details on how the interaction between KLIC-DA LT and the Altherma LT system starts.

 

 

Summary of Contents for KLIC-DA LT





















Reviews: