background image

 

 

 

KLIC-DA LT

 

http://www.zennio.com

 

Technical Support:

 

http://zennioenglish.zendesk.com 

 

10 

3

 

ETS PARAMETERISATION 

To begin with the parameterisation process of the KLIC-DA interface it is necessary, 
after launching the ETS program, to import the database of the product (

KLIC-DA LT

 

application program). 

Next, the device should be added to the project. And then, one right-click on the device 
will permit selecting "Edit parameters", in order to start the configuration. 

In the following sections a detailed explanation is provided about how to parameterise 
the different functionalities of the device in ETS. 

3.1

 

DEFAULT CONFIGURATION 

This section shows the default configuration the device configuration starts from. Note 
that no communication objects are enabled by default, so the device topology will show 
up empty. 

Regarding the parameter window, only one main tab (“General”) is shown, containing 
one sub-tab called 

Configuration

The following section describes all the parameters available under Configuration. 

 

Figure 4. 

The "Configuration" parameter window, under "General". 

 

 

 

Summary of Contents for KLIC-DA LT





















Reviews: