background image

8

5

9

INSTALLATION:

5.    (No picture)

    Fit the GPS antenna (No. 3) at a suitable place, 

and make sure that the GPS reception is not 

adversely affected due to shadowing by metallic 

vehicle parts (thermal glazing etc.). Next run the 

connecting cable to the radio slot.

6.    (No picture)

    If you wish to use it, now fit the external Blue-

tooth microphone (No. 4) supplied, and run the 

connecting cable to the radio slot. Depending 

on preference and on choice of an external or 

device-internal microphone, the microphone 

source for the Bluetooth mode must be corre-

spondingly changed in the device menu.

 

7.    (No picture)

    Run the USB extension cable (No. 9) from the 

radio slot to the position you want.

 

8.    Connect one of the main connection cables 

(No. 5 or No. 6) of the ZENEC system (No. 1) to 

the Quadlock connector of the car and close its 

locking mechanism. Please pay attention to the 

compatibility list in this document to choose the 

suitable main connection cable, including in the 

delivery, for your vehicle. Following this, connect 

the CAN bus interface (No. 7) to the main con-

nection cable.

 

9.    Before installing the ZENEC system (No. 1) 

remove the two transport securing screws.  

 

Summary of Contents for Z-E2026








Reviews: