Zelmer ZVC764CT, User Manual

Page: 53 / 56

59
28 Small atomizing nozzle
29 Water pick up nozzle
30 Rubber slat to the large atomizing nozzle
31 Washing set
32 Foam filter I (installed in the vacuum cleaner)
33 Foam filter II (installed in the vacuum cleaner)
34 Motor filter (installed in the vacuum cleaner)
35 EPA E10 / HEPA H13 outlet filter (installed in the vacuum
cleaner)
Preparing the vacuum cleaner for
operation
1
Insert the end of the suction hose to the vacuum cleaner
opening so that the markings on the hose end and on the
vacuum cleaner housing are opposite each other and turn
the hose clockwise to the position .
2
Connect the other end of the hose (handle) with the
telescopic suction tube.
3 Hold the ring on the pipe and set chosen length putting it
in or out.
4 Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5 Use the following nozzles and brushes for traditional
SAFBAG using the water filter module: combination
carpet & floor brush with small objects separator, small
nozzle, small brush, crevice nozzle, mattress nozzle, parquet
brush or turbo brush.
6 You may assemble a basket for picking up small objects
in the combination brush with small item separator. In order
to do so remove the basket cover and insert the basket.
7 To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the nozzle according to the figure .
8
The vacuum cleaner is equipped with an accessory
compartment. The compartment opens/closes with the use
of a slider. To open/close the compartment side the slider
downwards/upwards and take out/ put away the desired
nozzle.
9 The vacuum cleaner may be stored in a horizontal
position; in order to this, place the fastening hook of the
combination nozzle/brush into its fastening. The hose may
be left attached to the vacuum cleaner, but it is important to
pay attention not to leave it heavily bent during storage.
10 Close the lid.
11 Grab the plug (4) and pull the cord out of the vacuum
cleaner.
●
Plug in the appliance.
Before switching on the vacuum cleaner
with the on/off button (8), make sure that the
appropriate module is installed in the container
(see section C, E, or F).
B
12 Switch on the vacuum cleaner by pressing the “on/off”
button (8) .
In order to prepare the vacuum cleaner for wet operation
additionally:
13 Assemble the spray unit – the suction hose handle
attachment (26) .
●
Attach the hose fastenings to the suction hose and the
telescopic suction tube.
14 Attach the end of the hose (sleeve) to the telescopic
suction tube and insert the other end of the hose in the small
atomizing nozzle or the large atomizing nozzle until you hear
a characteristic click.
15 Use the following nozzles for the wet vacuuming and wet
cleaning function or to pick up water: large atomizing nozzle,
small atomizing nozzle or the water pick up nozzle.
16 Slide the stub pipe valve plug downwards.
●
Insert the stub pipe of the hose to the valve in the
vacuum cleaner housing.
●
Make sure the stub pipe fastenings snap shut.
In case of difficulties in connecting the above
mentioned elements moisten the gaskets e.g.
with technical vaseline, water, etc.
Vacuum cleaner functions
TRADITIONAL CLEANING WITH SAFBAG DUST BAG
1 Press and hold the container lid opening button (2) and
lift the container lid.
2
Put the SAFBAG holder (22) into the container. Make
sure the holder is inserted correctly in the container guide
slots and the safety lock is engaged. Unfold the bag in the
container.
Do not put SAFBAG holder into a wet container.
Thoroughly dry a wet container. SAFBAG dust
bag must not get wet.
3
Cover the container with the filtration unit.
If the SAFBAG holder is not attached properly,
the safety lock will prevent covering the
container with the filtration unit.
●
Prepare the vacuum cleaner for operation according
to section B.
4 The vacuum cleaner starts at the same power level it had
been working before it was turned off. Set the desired power
value by pressing the power adjustment b/- (9) .
The vacuum cleaner is equipped with a power
level memory function. When you turn off the
vacuum cleaner using the ON/OFF button
(8), the power level is going to be stored in
memory. After the vacuum cleaner is turned
on next time, it is going to start working at the
same power level it had been working before it
was turned off.
C