Zelmer ZVC764CT, User Manual

Page: 55 / 56

61
For protection against the formation of foam or at its
formation, when cleaning fill the rear container with an
anti-foaming agent (31) recommended by the company
ZELMER, in the amounts specified on the label:
–
“G 478 Buz
®
Defoam” manufactured by company BUZIL,
Germany.
●
Prepare the vacuum cleaner for operation according
to section B.
Use only the large or small atomizing nozzle for
wet vacuum cleaning.
●
The vacuum cleaner starts at the same power level
it had been working before it was turned off. Set the
desired power value by pressing the power adjustment
b/- (9) .
7 Press the pump switch (7) .
The pump may only be switched on when
the cleaning liquid container is filled with the
solution of cleaning liquid and water. The lack
of cleaning liquid manifests in a loud operation
of the pump.
If the nozzle does not atomize water although the pump
is switched on, check if the following items are correctly
installed: the cleaning liquid container (press the container),
the fastening of the stub pipe in the valve in the base of
the vacuum cleaner or the fastening of the hose end in the
atomizing nozzle, check if the atomizing nozzle is not clogged.
8 Press the button adjusting the inflow of water to the
nozzle on the hose handle.
If you press the button in a pulsating manner, the water shall
temporarily flow in a slower manner to the nozzle, if you
press and slide the button backwards, the water shall be
continuously supplied to the nozzle.
The handle is also equipped with a slider to adjust the
suction power. Do not uncover this opening while picking up
water or using the wet cleaning function.
Do not spray the cleaning liquid in one place
on the carpet for too long in order not to soak
the carpet.
●
You should to clean the carpet in such a way that during
and immediately after cleaning nobody walks on the
cleaned surface. After cleaning one part of the carpet
stop the spraying process and dry the carpet by sliding
the nozzle back and forth. Repeat until the whole surface
of the carpet is dried.
●
After ending the spraying process switch off the pump
and press the button adjusting the water inflow to the
nozzle for a moment to “release the pressure”.
The vacuum cleaner is equipped with a float
which will automatically block the suction if
the foam filter II (33) is heavily dirty or the liquid
exceeds the maximum level. It is manifested
by a pulsing limitation of the motor power and
the lighting up of the clogged air inlet indicator
(12). In such a case switch off the vacuum
cleaner by pressing the on/off button (8), unplug
the appliance, clean the filter and empty the
container.
Make sure the carpet is not soaked. It may
lead to a permanent deformation of the carpet
(folding).
PICKING UP WATER
If you want to use the vacuum cleaner to vacuum liquid in
the container, the vacuum cleaner should be prepared as in
the case of vacuum cleaning with the use of the water filter
module except that:
1. The container should be empty (without water).
2. You are to use atomizing nozzles (large or small), large
atomizing nozzle with the gathering attachment or the
nozzle for picking up water.
Do not operate the vacuum cleaner with a full
container! Do not vacuum large amounts of
liquid at a time (e.g. with the hose immersed
into water).
If the water exceeds the maximum level during vacuuming,
the float will automatically block the suction. The maximum
capacity of the container is about 5 l. In such a case proceed
in the manner described above in the part concerning the
blocking of suction caused by a dirty foam filter (pulsating
motor speed).
END OF OPERATION CLEANING AND MAINTENANCE
●
Switch off the vacuum cleaner by pressing the on/off
button (8) and unplug the appliance.
●
Wind the cord by pressing the cord rewind button (9) .
While doing this hold the cord to make sure it is not
tangled and the plug does not hit the vacuum cleaner
housing.
●
Turn the end of the hose until the tops of the marks
on the end of the hose end and on the vacuum cleaner
housing are in the same position and pull the hose out
of the opening.
●
Remove the stub pipe of the hose by pressing the red
button on the valve and pull the stub pipe.
●
Disconnect the telescopic tube from the hose and the
nozzle or brush.
●
Pour the dirty water out of the container.
●
It is recommended to wash the container, filters
(disassembly below) and partition thoroughly after each
use – changing water several times.
●
After using the wet cleaning function thoroughly wash
all attachments used in this process (hose, tubes,
accessories).
If you do not clean the above-mentioned parts
or clean them insufficiently it may lead to the
loss of the filtration capabilities of the inserts
and foam and cause the formation of bacteria
and mites.