Zelmer ZVC345SA, User Manual

Page: 46 / 48

52
ZVC345-001_v02
Examples of problems while operating the
vacuum cleaner
PROBLEM ACTION
A characteristic “fluttering”
of the vacuum cleaner is
heard.
• Check the dust bag and the
accessories, remove the cause of the
clogging or replace the dust bag with
a new one.
• Clean the vacuum cleaner chamber
and the filter.
The dust bag is damaged. Remove the dust bag and the filters.
The electrical installation
fuse went out.
Check if other appliances are not
plugged to the same electrical circuit
as the vacuum cleaner. If the fuse
goes out repeatedly, return the vacuum
cleaner to a service point.
The vacuum cleaner does
not operate; the housing or
the cord is damaged.
Return the vacuum cleaner to
a service point.
The suction power of the
vacuum cleaner is weak.
Replace the dust bag and the filters,
check the suction tube, the hose and
the nozzle – remove the cause of the
clogging.
Ecology – Environmental protection
Each user can contribute to protect the environment. It is
neither difficult nor expensive. In order to do so:
Return cardboard packages to recycling
points.
Throw polyethylene (PE) bags into appropriate
containers.
Return a worn out appliance to an appropriate
collecting point as the components of the
appliance may pose a threat to the environment.
Do not dispose of with household waste!
3 Remove the EPA filter case and replace it with a new
one. The EPA filter ensures an effective operation of the
vacuum cleaner for about 1 year.
4 Insert the cover so that the two protrusions in the lower
part of the cover are inserted in the openings of the vacuum
cleaner body, press the filter cover so that the rear fastenings
snap shot on the body.
INLET FILTER
1
Release the upper cover fastening (12) and open the cover.
2 Remove the SAFBAG dust bag module (18) from the
vacuum cleaner chamber.
3 Slide the inlet filter casing with the installed inlet filter
from the tracks on the back side of the vacuum cleaner
chamber.
4 Remove the inlet filter (16) from the inlet filter casing.
5 Place the new filter in the inlet filter casing (17) with the
material side directed towards the inside of the casing.
6
Slide the inlet filter casing (17) together with the filter in
the tracks until stop to the previous position.
Always replace a damaged inlet filter (16) with
a brand new, original one.
7
Insert the SAFBAG dust bag module to the vacuum
cleaner chamber.
8 Close the cover by pressing it until you hear
a characteristic click – pay attention not to trap the dust bag.
End of operation cleaning and
maintenance
1 Switch off the vacuum cleaner by pressing the “on/off”
button (7) .
2
Unplug the appliance.
3 Wind the cord by pressing the cord rewind button (4) .
While doing this hold the cord to make sure it is not tangled
and the plug does not hit the vacuum cleaner housing.
4 Disconnect the telescopic tube from the nozzle or brush.
5 Disconnect the telescopic tube from the hose. In order to
remove the tube from the hose handle press the “A” locking
device and pull the tube in the direction of the arrow.
6
Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
7 The vacuum cleaner may be stored vertically or
horizontally. In order to do so, insert the fastening hook of the
combination brush to the combination brush fastener. The
hose may be attached to the vacuum cleaner, however you
have to make sure that it is not excessively bent during storing.
8
If necessary wipe the housing and the dust bag container
with a damp cloth (it may be soaked with dishwashing liquid)
and dry it or wipe until dry.
Do not use abrasive detergents or solvents.
E
F
The importer/manufacturer does not accept any liability for any
damages resulting from unintended use or improper handling.
The importer/manufacturer reserves his rights to modify the product
any time in order to adjust it to law regulations, norms, directives,
or due to construction, trade, aesthetic or other reasons, without
notifying in advance.