Zelmer ZVC241SP, User Manual

Page: 44 / 47

44
ZVC241-001_v01
15 “CYCLONE” module
16 “CYCLONE” dust container (vacuum’s removable module)
17 Upper lid of the “CYCLONE” dust container
18 Bottom lid of the “CYCLONE” dust container
19 Combination suction brush
20 Crevice nozzle
21 Small brush
22 Small nozzle
23 BNB (Brush Natural Bristle) floor brush
Is used to clean and polish hard, scratch sensitive
surfaces such as wooden floors, floor panels, parquet,
marble, tiles, etc.
Delicate and soft natural bristles ensure maximum
vacuum effectiveness and protects against scratching
the cleaned surface.
Preparing vacuum cleaner for operation
1 Put the end of the suction hose to the inlet of the vacuum
cleaner. A characteristic “click” signalizes the hose has been
properly installed.
2 Connect the other end of the hose (handle) with the
suction tube. In order to do it, press latch ”A” and insert the
tube into the hose’s handle so that latch “A” is blocked in
opening “B” .
3 Adjust the telescopic suction tube to the desired length
by sliding the slider according to the arrow and pull the tube
out/in.
4 Attach the selected nozzle or brush to the other end of
the suction tube.
5
Combination suction brush may be used to vacuum hard
flooring and carpets. In order to vacuum hard surfaces –
wooden, plastic floors, ceramic tiles, etc. pull the brush out
by pressing the switch on the suction brush according to the
drawing
. When vacuuming carpets, hide the brush
(set the switch on the suction brush to “ ”).
6 Grab the plug (3) and pull the cord out.
When pulling the power cord out, beware of
the yellow stripe signaling the end of the cord.
Persistent pulling (pulling on), may damage the
cord.
7 Insert the plug into the power outlet.
Before starting the vacuum, make sure that both “CYCLONE”
dust container has been fitted with the basic EPA E11 filter
and the outlet filter has been installed.
8 Switch the vacuum cleaner on by pressing ON/OFF
button (5) .
9 The vacuum cleaner is equipped with an electronic
controller of suction power, which enables smooth regulation
of suction power of the vacuum cleaner. By moving the slider
(6) right (MAX) and left (MIN) you may respectively increase
or decrease the suction power.
B
Technical parameters
The type of the vacuum cleaner and the technical parameters
are indicated on the rating label. Mains protection 16 A.
Does not cause interferences with audio/video devices.
The device meets the requirements of Commission
Regulation (EU) No. 666/2013 on implementing the Directive
of the European Parliament and of the Council 2009/125/EC
with regard to eco-design requirements for vacuum cleaners.
The device complies with the requirements of the
Commission Delegated Regulation (EU) No. 665/2013
supplementing Directive of the European Parliament and of
the Council 2010/30/EU with regard to energy labelling of
vacuum cleaners.
Noise level: max. 80 dB(A).
Static electricity
In the process of vacuuming of some surfaces in areas of
low air humidity the device may become electrically charged.
It is a natural phenomenon – it does not damage the device,
and it is not considered to be a fault.
In order to minimize the phenomenon, we recommend you to:
●
discharge the device by touching metal items in the room
with the pipe,
●
increase air humidity in the room,
●
use widely available antistatic agents.
Appliance elements
A
1 Outlet filter cover
2 Suction brush fastening clip
3 Plug and cord
4 “CYCLONE” dust container release lever
5 ON/OFF button
6 Suction power regulation slider
7 Cord rewind button
8 Handle
9 Slider – mechanical regulator of the suction power
10 Suction hose
11 Telescopic suction tube
12 Outlet filter “Microfilter” (fitted inside the vacuum)
13 Basic EPA E11 filter (fitted inside “CYCLONE” dust
container)
14 “CYCLONE” cartridge
●
Product data sheet provided with the vacuum cleaner
showing the technical parameters is an integral part of
the instruction manual.
●
Vacuum cleaners with the energy efficiency class A do
not work with ZELMER Turbo Brush Type VB1000.
●
Product data sheet provided with the vacuum cleaner
showing the technical parameters is an integral part of
the instruction manual.