Zelmer zvc125-001, User Manual

Page: 37 / 40

43
ZVC125-001_v02
Due to safety reasons, it is vital never to install
a damp inlet filter (11).
5 Install a new/the rinsed inlet filter (11) , making sure that
the whole filter is in the socket.
6
Insert a bag into the vacuum cleaner chamber (see p. E).
7 Close the front cover of the vacuum cleaner.
The damaged inlet filter should be replaced with
a new, genuine manufactured product only.
OUTLET FILTER „MICROFILTER”
1
Press the lock and open the cap of the outlet filter, then
pull the cap out of the cleaner.
2 Take the used outlet filter out (12) .
●
If the outlet filter (12) is dirty wash it in running water.
Remember to dry the filter before putting it into the
cleaner.
3
Put new/washed filter into the cleaner.
Due to safety precautions never put wet outlet
filter into the cleaner.
4
Put the cap so as to two ledges in the lower part of the
cap match the holes in the cleaner body, close the cap by
pressing it until you hear a characteristic “click”.
Damaged outlet filter should be always
replaced with a new original one.
Dust bag disassembly/assembly
DOT vacuum cleaner is equipped with both SAFBAG bag
(1 piece) as well as a reusable bag (1 piece).
1 Total covering up of bag loading indicator by the red
cover in case the sucker or the brush is upraised over
the cleaned surface informs, that change of dust bag is
necessary. The bag loading indicator may operate in case
of suction hose stopping or in case of stopping of equipment
elements connected thereto.
2 Switch off the vacuum cleaner by pressing the on/off
button (3) .
3
Unplug the appliance.
4 Open the front cover handle (9) .
5 Press the side button on the end of the hose, then
remove the end of the hose from the inlet hole of the vacuum
cleaner.
6
Release the hook locking the bag holder according to
the arrow on the hook and then remove the bag with the
handle up.
7 Put out the bag plate from the holder. Dump the filled bag
into the garbage.
8
Caution! Do not throw the bag holder.into the trash.
9 Slide the plate of a new bag into the handle and slide it
until the end of the handle.
D
E
10 Insert the handle with the new bag into the seat of casing
and lock it with the locking hook.
Carefully place the bag in such a way that the
hole in the bag plate was placed over the rubber
collar in the chamber of the vacuum cleaner.
11 Close the cover until you hear the characteristic clicking
sound – be careful not to catch the bag.
In case of using a reusable bag:
12 Release the bag fastening according to the arrow on it
and then pull the bag up to remove it.
13 Slid the closing board on the back part of the bag down
and empty out the contents.
If the bag is very dirt, you can wash it in water
with a little amount of washing agent.
If the bag was washed, it should be dried
before it is used again.
14
Place the closing board on the back part of the emptied
bag.
15 Slid the bag into its place.
Carefully place the bag in such a way that
the hole in the bag plate was placed over the
rubber collar in the chamber of the vacuum
cleaner.
●
Close the cover by pressing it until you hear a distinctive
click – be careful not to get the bag caught.
Do not vacuum without bag. In case if there is
no bag in the vacuum cleaner, the front cover
of the vacuum cleaner cannot be locked.
You should replace the bag, if:
a) the red field covers the bag full indicator,
b) the vacuum cleaner operates poorly,
c) the dust bag is full.
The number of SAFBAG bags set that can be purchased,
is placed on a sticker located in the vacuum chamber.
Special accessories
The following special accessories may be purchased in retail
outlets:
Parquet brush “BNB” (20)
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble, tiles, etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.