64
VC1400-001_v02
Special accessories
The following special accessories may be purchased in retail
outlets:
Parquet brush “BNB” (22)
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble, tiles,
etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
Zelmer turbobrush (23)
May be used with all types of ZELMER vacuum cleaners.
Is used for an effective vacuuming of carpets and fitted
carpets. While using the turbobrush follow the instruction
manual.
The use of the turbobrush decidedly increases the
effectiveness of removing fibrous dirt such as: animal hair,
hair, threads etc. It is practically useful in households with
pets (cats, dogs), where removing the animal hair from the
carpets and floorings is very onerous.
After-work procedures, cleaning and
maintenance
1
Press the on/off button to stop the vacuum cleaner.
2
Remove the plug of the cord from the socket.
3
Wind the cord by pressing the cord winder button
(8)
.
Hold the cord when doing it to avoid tangling the cord up or
letting the plug hit the vacuum cleaner.
4
Disconnect the telescopic suction pipe from the nozzle or
brush.
5
Disconnect the suction tube from the hose. In order
to remove the telescopic tube from the hose handle,
simultaneously press the lock
A
and pull the tube in the
direction indicated by the arrow.
6
Turn the end of the suction hose counter-clockwise, and
remove the end of the hose from the inlet of the vacuum
cleaner.
7
The vacuum cleaner may be store in a horizontal
position. In order to do this place the hook of the nozzle
brush into the fastening of the nozzle brush situated at the
back of the vacuum cleaner, near the entrance of the power
cord. The hose may stay attached to the vacuum cleaner as
long as it is not bent too much during storage.
8
If necessary, clean the casing and the chamber of the
vacuum cleaner with a damp cloth (it may be damped in
dishwashing liquid), dry it off, and wipe it dry.
Do not use any scrubbing agents or solvents.
F
4
Place the new/rinsed HEPA H12 basic filter
(14)
in the
previously determined spot in the dust container.
5
Situate the protective casing of the HEPA H12 basic filter
in the chamber of the container, in the previously determined
spot. Pay attention that the protrusions situated on the flange
of the container are inserted in the sockets of the body of the
container.
6
Turn the protective casing of the HEPA H12 basic filter
in the direction given on the symbol „ ” (it is situated along
with an arrow on the protective casing of the HEPA H12 basic
filter).
7
Place the cover of the CYKLON dust container on the
container in such a way that the fastening situated in the
front part of the cover is inserted into the projection of the
container. Press the back part of the cover in such a way that
the fastenings are shut tight on the body of the container.
8
Situate the CYKLON dust container with the installed
HEPA H12 basic filter
(14)
in the chamber of the vacuum
cleaner. Close the upper cover of the vacuum cleaner by
pressing it, until you hear a characteristic “click.”
We advise you to replace the HEPA H12 basic
filter (14) with a new one every 6 months of
use.
Always replace a damaged HEPA H12 basic
filter with a brand new, original one.
OUTLET MICROFILTER
1
In order to replace the outlet microfilter
(13)
press the
blocking mechanism on the cover of the outlet filter, and then
remove the cover of outlet filter out of the vacuum cleaner.
2
Remove the outlet filter from the cover.
If the outlet microfilter
(13)
is dirty, you may replace it with
a new one, clean it or rinse it with running water. Before
reinstalling the filter, make sure it is dry.
For safety reasons, it is unacceptable to install
a wet or damaged outlet microfilter.
3
Situate the new/rinsed filter carefully onto the
4 fastenings of the outlet filter cover with the foam sides
towards themselves.
4
Place the filter cover in such a way that the two
protrusions situated in the lower part of the cover are
inserted into the holes in the body of the vacuum cleaner,
and then press the filter cover to snap the fastening in the
body shut. A characteristic “click” signalizes the filter cover
has been properly installed.
Always replace a damaged microfilter with
a brand new, original one.
E
Summary of Contents for Tiny VC1400
