Zelmer Ceres, User Manual

Page: 62 / 62

66
VC3300-001_v01
3 Remove the tube of the CYKLON dust container from the
container.
4 If the tube of the CYKLON dust container (19) is dirty,
it may be rinsed with running water. Before reinstalling the
tube, make sure it is dry.
5 Insert the rinsed tube of the CYKLON dust container into
the socket of the container in such a way that the protrusion
situated on the flange of the tube is situated in the socket of
the body of the container. The other end of the tube is to be
inserted into the round socket situated on the bottom of the
chamber, where the tube is placed.
6 Snap the bottom of the CYKLON dust container shut.
Pay attention that the seal on the bottom of the container
remains correctly placed.
7
Place the emptied CYKLON dust container into the
chamber of the vacuum cleaner. A characteristic “click”
signalizes the container has been properly installed.
Special accessories
The following special accessories may be purchased in retail
outlets:
Parquet brush “BNB” (25)
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble, tiles, etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
After-work procedures, cleaning, and
maintenance
1 Press the on/off button (4) to stop the vacuum cleaner.
2 Remove the plug of the cord from the socket.
3 Wind the cord by pressing the cord winder button (7) .
Hold the cord when doing it to avoid tangling the cord up or
letting the plug hit the vacuum cleaner.
4
Disconnect the telescopic suction pipe from the nozzle or
brush.
5 Disconnect the telescopic suction pipe from the hose.
6
Press the button situated on the end of the hose, and
remove the end of the hose from the inlet of the vacuum
cleaner.
7 The vacuum cleaner may be store in a vertical or horizontal
position. The hose may stay attached to the vacuum cleaner
as long as it is not bent too much during storage.
Horizontal storage:
place the hook of the nozzle brush into the fastening
–
of the nozzle brush situated at the back of the vacuum
cleaner, near the entrance of the power cord.
Vertical storage:
place the nozzle brush on the telescopic pipe,
–
then insert the hook of the telescopic pipe into the
–
fastening situated on the bottom of the vacuum cleaner,
near the front wheel.
G
4 Situate the CYKLON dust container with the installed
HEPA inlet filter (16) in the chamber of the vacuum cleaner.
A characteristic “click” signalizes the container has been
properly installed.
We advise you to replace the HEPA inlet filter
(16) with a new one every 6 months of use.
Do not use the vacuum cleaner without the
HEPA inlet filter (16) installed in the CYKLON
dust container. If the HEPA inlet filter is not
there, it is impossible to situate the CYKLON
dust container in the vacuum cleaner.
FOAM OUTLET FILTER
1 In order to replace the foam outlet filter (14) press the
fastening on the cover of the filter, and remove the cover of
the filter from the vacuum cleaner.
2 Pull the handle situated on the frame of the foam outlet
filter (15) to the right, pull the frame aside towards you, and
remove it from the vacuum cleaner.
3
Remove the foam outlet filter from the frame.
If the foam outlet filter (14) is dirty, you may replace it with
a new one, clean it or rinse it with running water. Before
reinstalling the filter, make sure it is dry.
For safety reasons it is unacceptable to install
a wet or damaged foam outlet filter (14).
4 Place the new/rinsed filter carefully into the frame.
5
Situate the frame with the foam outlet filter (14) into the
vacuum cleaner, so that both of the fastenings on the right side
are fitted into the holes in the body of the vacuum cleaner.
6
Block the frame from its left side in such a way that the
fastenings of the frame are inserted into the holes in the body
of the vacuum cleaner.
7
Place the filter cover in such a way that the two
protrusions situated in the lower part of the cover are
inserted into the holes in the body of the vacuum cleaner,
then press the filter cover to snap the fastening in the body
shut. A characteristic “click” signalizes the cover has been
properly installed.
Do not use the vacuum cleaner without the inlet
filters and the outer filter installed.
Always replace damaged filters with original,
brand new ones.
TUBE OF THE CYKLON DUST CONTAINER
It is necessary to periodically clean the tube of the CYKLON
dust container.
1 Remove the CYKLON dust container and empty it, as
described in para. C .
2 Press the button situated on the CYKLON dust container,
and open its bottom. If the CYKLON dust container is full,
empty it as described in para. C .
E
F