Zelmer 490.30NP, User Manual

Page: 43 / 46

47
490-004_v01
Before shredding big pieces of the products
cut them into smaller ones – approximately
1 cm cubes.
Never disassemble the lid from the container
before the disc stops rotating.
Operational guidelines
The dismantling process should be done in reverse order
●
to assembly.
The operating time of the blended equipped with the food
●
processor cannot exceed 2 minutes. Allow the motor to
cool before proceeding.
Do not start – up the motor without accessories.
●
When finished, turn the appliance off and unplug it by
●
disconnecting the cable cord from the power outlet.
If the products stick to the blade or the walls of the
●
container:
Switch off the appliance.
–
Remove the drive with the lid and container of ice or
–
other products crusher.
Remove the products out of the mini food processor
–
walls.
Re-assemble the appliance – as defined above,
–
Continue the operation.
Approximate time for processing of selected
products for the recommended gear
Product
Recommended
gear
Processing
time
TURBO 20-30 s
TURBO 25-30 s
1/4
8 15 s
12
+TURBO
40 s + 5 s
(
×30
) 12 10 s
12
+TURBO
15 s + 5 s
TURBO 30 s
You can shorten the processing time as you wish, then you
obtain other granulation of grinded products.
OPERATING THE FOOD PROCESSOR
The appliance characteristics
ZELMER Hand blender is equipped with a food processor
which is used for chopping, liquidizing, slicing, and grating
fruits and vegetables.
The application of the food processor accessories
Double – sided slicing disc – is used to slice fruit and
vegetable (raw, boiled) into thin or thick slices. The slicing
disc is round, with double -sided blades (one side for thin
slices, the other side for thick slices).
Double – sided chipping and puree disc – is used for
chipping and pureeing fruit and vegetables. Chipping and
puree disc is round, with double -sided blades (one side for
chipping i.e. carrots, celery boiled beetroots, the other side
for pureeing – i.e. for potato pancakes, beetroot salad).
Disc driver – is used for assembling discs (for slicing,
chipping and pureeing).
Pusher – is used for pushing product grinded with all discs
and closing the lid feed chute.
Use permanent guard for all shields of the food
processor.
The slicing and pureeing process cannot last
longer than 2 min. After this time, wait until
the motor cools down before next usage of the
blender.
Preparing the food processor to use
Before assembling on and removing the blender
drive out of the food processor, make sure that
the plug of the supplying cord is disconnected
from the mains supply outlet.
Wash the parts in contact with processed product before
first usage.
Operate the blender so, that the closed/open markings
located on the appliance are well visible .
Operating the food processor (Fig. E)
1 Place the base of the food processor on firm, flat and
dry surface. Insert the food processor container into the base
fasteners.
2 Lock the container.
Operation with food processor (slicing disc,
chipping and puree disc) (Fig. F)
1 Place the selected disc on the disc driver (double-sided
discs) so that the blades provided for operation are on the top.
2 Insert the accessory inside the container, so that it is
connected with the drive shaft.
3 Insert the permanent guard. The guard can be assembled
inside the food processor container in one position only, so
200 g
(500 ml)
20 g
(500 ml)
300 g
300 g
(500 ml)
250 g
(500 ml)
200 g
(500 ml)
1 cm
1 cm
250-300 g
(400-500 ml)