Zelmer 1600, Instruction Manual, Page: 45 / 50

51
1600-016_v01
a given filter: H11 filter retains 95.5% of particles with the
size of 0.3 micron and H13 filter retains as much as 99.95%
of all pollutants.
1
The HEPA outlet air filter needs to be replaced when the
surface of the filter is dirty or the control lamp of the outlet
filter replacement indicator lights up (9) (pulsing red light).
The suction power of the vacuum cleaner will reduce to
setting 1 when the outlet filter replacement indicator lamp
lights up.
2 To replace the HEPA filter lift the vacuum cleaner handle
and open the accessory compartment.
3 Grab the outlet filter cover (8) by the two fastenings,
press firmly with the thumbs and pull it to the outside.
4 Remove the HEPA filter case and replace it with a new
one. The HEPA filter ensures an effective operation of the
vacuum cleaner for about 1 year.
Insert the cover so that the two protrusions in the lower part
of the cover are inserted in the openings of the vacuum
cleaner body, press the filter cover so that the rear fastenings
snap shot on the body.
SAFBAG dust bag disassembly/assembly
E
1
The vacuum cleaner is equipped with a safety valve
which is located in the dust container (bag) chamber. It
opens automatically when the suction hose or the elements
attached to the suction hose are completely clogged or when
the dust bag is overfilled with dust. After the opening of the
valve a characteristic “fluttering” in the vacuum cleaner will
be heard. The opening of the safety valve will result in the
lighting of the dust bag full indicator.
2 When the dust bag full indicator (14) lights (with the
nozzle or the brush lifted above the cleaned surface) it means
that the bag is full and needs to be replaced. In addition the
dust bag full indicator may activate if the suction hose or the
elements attached to the suction hose are clogged.
3
Switch off the vacuum cleaner by pressing the “on/off”
button (2) and unplug the appliance.
4 Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
5 Release the front cover fastening (15) and open the
cover.
6 While holding the dust bag plate, gently bend it towards
the inside of the dust container chamber and remove the
whole dust bag upwards.
7 Insert the plate of the new dust bag in the tracks and
slide the plate together with the screen to the bottom of the
container, unfold the dust bag. The direction for inserting the
dust bag is indicated by the arrow on the bag.
8 Close the cover by pressing it until you hear
a characteristic click – pay attention not to trap the dust bag.
ZELMER vacuum cleaners are equipped with SAFBAG dust
bags in the amount indicated in the table. It is recommended
to replace the dust bag if:
a) the dust bag full indicator lights up,
b) the safety valve activates,
c) the vacuum cleaner operates poorly,
d) the dust bag is full.
Special accessories
The following special accessories may be purchased in retail
outlets:
Zelmer turbobrush (26)
May be used with all types of ZELMER vacuum cleaners. Is
used for an effective vacuuming of carpets and fitted carpets.
While using the turbobrush follow the instruction manual.
The use of the turbobrush decidedly increases the
effectiveness of removing fibrous dirt such as: animal hair,
hair, threads etc. It is practically useful in households with
pets (cats, dogs), where removing the animal hair from the
carpets and floorings is very onerous.
Zelmer electrobrush (27)
Only the electrobrush manufactured by ZELMER may be
used with ZELMER vacuum cleaners. Using other brands of
electrobrushes may cause damage to the vacuum cleaner.
The electrobrush may be used with all ZELMER vacuum
cleaners equipped with the appropriate electrobrush socket.
While using the electrobrush follow the instruction manual.
The electrobrush is especially helpful in cleaning worn out
carpets. Before vacuuming remove all larger elements from
the floor such as: remains of cloth, paper etc. in order to
prevent blocking of the whirling element of the brush.
End of operation cleaning and
maintenance
1 Switch off the vacuum cleaner by pressing the “on/off”
button (2) .
2 Unplug the appliance.
3 Wind the cord by pressing the cord rewind button (4) .
While doing this hold the cord to make sure it is not tangled
and the plug does not hit the vacuum cleaner housing.
4
Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
5 Disconnect the telescopic tube from the nozzle or brush.
6 Disconnect the telescopic tube from the hose. In order to
remove the tube from the hose handle press the “A” locking
device and pull the tube in the direction of the arrow.
7 The vacuum cleaner may be stored horizontally. The
hose may be attached to the vacuum cleaner, however
you have to make sure that it is not excessively bent during
storing.
8 If necessary wipe the housing and the dust bag container
with a damp cloth (it may be soaked with dishwashing liquid)
and dry it or wipe until dry.
Do not use abrasive detergents or solvents.
F