
49
1600-016_v01
Technical parameters
The type of the vacuum cleaner and the technical parameters
are indicated on the rating label. Mains protection 16A. Does
not cause interferences with audio/video devices.
Does not require grounding
.
ZELMER vacuum cleaners meet the requirements of the
applicable norms.
The appliance is in conformity with the requirements of the
directives:
Low voltage appliance (LVD) – 2006/95/EC.
–
Electromagnetic compatibility (EMC) – 2004/108/EC.
–
Noise level: 80 dB/A.
The appliance was marked by a CE sign on the rating label.
Static electricity
In the process of vacuuming of some surfaces in areas of
low air humidity the device may become electrically charged.
It is a natural phenomenon – it does not damage the device,
and it is not considered to be a fault.
In order to minimize the phenomenon, we recommend you to:
discharge the device by touching metal items in the room
●
with the pipe,
increase air humidity in the room,
●
use widely available antistatic agents.
●
Appliance elements
A
1
Electrobrush socket
2
ON/OFF button
3
Handle
4
Cord rewind button
5
Combination brush fastening
6
Accessory compartment cover
7
Plug and cord
8
Outlet filter cover
9
Filter wear indicator
10
Power increase button
11
Suction power level indicator
12
Power decrease button
13
Infrared receiver (type 1600.3)
14
Dust bag full indicator
15
Front cover fastening
16
Infrared transmitter (type 1600.3)
17
STANDBY mode button (type 1600.3)
18
Suction hose. The vacuum cleaner is equipped with one
suction hose (A or B)
A
Suction hose (type 1600.0)
B
Suction hose with remote power control (type 1600.3)
19
Outlet filter. The vacuum cleaner is equipped with only
one outlet filter (A or B)
A
Outlet filter HEPA H13 (type 1600.3 HT, 1600.3 HQ)
(installed in the vacuum cleaner)
B
Outlet filter HEPA H11 (type 1600.0 SP, 1600.0 ST)
(installed in the vacuum cleaner)
20
Inlet filter (installed in the vacuum cleaner)
21
SAFBAG dust bag (2 pieces)
22
Telescopic suction tube
23
Small brush
24
Crevice nozzle
25
Small nozzle
26
Turbobrush (type 1600.0 ST, 1600.3 HT)
27
Electrobrush (type 1600.3 HQ)
28
Combination brush. The vacuum cleaner is equipped
with only one type of combination brush (A or B)
A
Switchable combination brush
B
Combination brush with a small item separator
29
Parquet brush “BNB”
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble, tiles,
etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
Preparing the vacuum cleaner for
operation
1
Insert the curved hose end in the opening of the vacuum
cleaner and gently press. A characteristic click indicates that
the hose has been properly installed.
2
Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device
“A”
and slide the tube into the hose handle so that
the locking device
“A”
is blocked in opening
“B”
.
3
Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/pull the tube
together.
4
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5
You may assemble a basket for picking up small objects
in the combination brush with the small item separator. In
order to do so remove the blank cover and insert the basket.
6
To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the combination brush according to the figure
.
7
Grab the plug
(7)
and pull the cord out of the vacuum
cleaner.
While puling out the cord pay attention to the
yellow stripe which signals the end of the cord.
Further attempts (pulling on cord) may result in
damaging the cord.
8
Plug in the appliance.
B
Summary of Contents for 1600
