background image

 

INTRODUCTION 

Carl Zeiss 

General information 

Fluar Illuminator Z mot. 

 
 

 

435180-9060-701 

05/2012 

1

 

INTRODUCTION 

1.1

 

General information 

Fluar  Illuminator Z mot. and the Axio Zoom.V16 microscope have been designed, manufactured and 
tested in compliance with DIN EN 61010-1 (IEC 61010-1) and IEC 61010-2-101 Safety requirements for 

electrical equipment for measurement, control and laboratory use. 
The Fluar Illuminator Z mot. and Axio Zoom.V16 zoom microscope meet the requirements of EC Directive 
IvDD 98/79/EC (In vitro diagnostic medical devices); they are marked with the 

 mark. 

The operating manual contains all information and warnings the operator must comply with. 
The following warning and information symbols are used in this operating manual: 

 

CAUTION

 

This symbol indicates a potential hazard to the user.

 

 

CAUTION

 

 

Optical radiation is emitted. Do not look into the laser beam!

 

 

This may be harmful to the eyes (see Section 2.3).  

 

CAUTION

 

Risk of pinching!

 

 

CAUTION

 

Hot surface!

 

 

CAUTION: High-energy UV radiation!

 

 

Risk of injury to eyes and skin!

 

 

CAUTION

 

Disconnect the instrument from the power supply before opening!

 

 

ATTENTION

 

This symbol indicates a potential hazard to the instrument or system.

 

 

NOTE

 

This symbol indicates an instruction which requires particular attention.

 

 
 

Summary of Contents for Fluar Illuminator Z mot.























Reviews: