background image

Unpacking and preparation

All units are carefully inspected 
at the factory throughout the 
entire fabrication and assembly 
processes under Zehnder 
Rittling’s stringent quality 
assurance program. All major 
components and subassemblies 
such as motors, blowers, 
coil, controls, valve package 
and paint quality are carefully 
tested for proper operation, 
visually inspected and verified 
for full compliance with factory 
standards. Operational testing 
for some customer furnished 
components such as pneumatic 
valves and DDC controllers may 
be a possible exception.

Cabinet Unit Heaters are usually 
shipped on pallets of up to 5 
units. Each unit is factory tagged 
according to the customer’s 
purchase order. This allows the 
unit, upon removal from the 
pallet, to be taken directly to its’ 
assigned space for immediate 
installation. Units should not be 
installed at locations other than 
that designated on the tag.

Each unit is carefully packaged 
in a polyethylene plastic bag 
for surface protection, placed 
in a cardboard container and 
filled with kraft paper padding 
for shipment to avoid damage 
during normal handling in the 
shipment process. It is the sole 
responsibility of the customer 
to provide the protection 
necessary to prevent vandalism 
and weather deterioration 
of the equipment. Under no 
condition should the units 
be left unprotected from the 
elements. If the equipment is 
not needed immediately at the 
job site, it should be left in its 
shipping carton and stored in 

if foreign material is allowed to 
be deposited on the motor or 
blower wheels of any unit. Some 
job conditions may require some 
form of temporary unit covering 
during construction.

DO NOT store or install units 
in corrosive environments or in 
locations subject to temperature 
or humidity extremes (e.g., 
attics, garages, rooftops, etc.). 
Corrosive conditions and high 
temperature or humidity can 
significantly reduce system 
performance, reliability and 
overall service life.

a clean, dry area of the building or 
in a warehouse. Do not remove any 
equipment from its shipping package 
until it is needed for installation. 
The equipment is NOT suitable for 
outdoor installations.

After determining the condition of 
the cardboard container exterior, 
carefully remove each unit from the 
container and inspect for hidden 
damage. At this time, check that all 
shipped loose items such as wall 
mounted thermostats, aquastats, 
remote temperature sensors, valve 
package, etc., are accounted for and 
placed in a safe area. Any hidden 
damage should be recorded and 
immediately reported to the carrier 
and a claim should be filed. In the 
event a claim for shipping damage is 
filed, the unit, cardboard container, 
and all packing must be kept for 
physical inspection by the freight 
carrier.

Once the equipment is properly 
positioned on the job site, cover 
the units with either a shipping 
carton, vinyl film, or an equivalent 
protective covering. Cap open ends 
of piping that is stored on a job site. 
Take special care to prevent foreign 
materials from entering the units in 
areas where painting, dry walling, 
or spraying of fireproof material, 
etc., has not yet been completed 
as these materials may accumulate 
on the motors and blower wheels. 
Foreign material that accumulates 
within the units can prevent proper 
start-up, necessitate costly clean-up 
operations, or result in immediate 
or premature component failure. 
Before installing any of the system 
components, be sure to examine 
each pipe, fitting and valve, and 
remove any dirt or foreign material 
found in or on these components. All 
manufacturer’s warranties are void 

13

Unpacking and preparation

Summary of Contents for RC-360

































Reviews: