Zebra Dazzle Manual Download Page 10

Page: 10 / 12

Zebra™ Dazzle™ Sump Level Controller

If you have questions or require product support, please call 888.249.4855.

Programming the Sump Controller Unit

Perform the following steps to set the Sump Controller unit to Operating mode.

1. Press and hold the programming button until the unit beeps once. Release the button. The lower 8

LEDs are yellow. This LED pattern is the Set High Level pattern.

2. Place the level of the sump to its maximum level (high level) or immerse sensor in sump to the

desired high fluid level. Press and hold the programing button until the unit beeps twice. Release

the button. The LEDs are now in the Set Low Level pattern.

3. Place the level of the sump to its minimum level (low level) with all machines and attachments

operating, or immerse sensor in sump to the desired low fluid level. Press and hold the programing

button until the unit beeps twice. Release the button. While the unit is beeping, the LEDs briefly go

into the Controller Configured pattern. They then settle into the Operating Mode pattern. The Sump

Controller unit is ready to be used.

Figure 7. Set High Level pattern

Figure 8. Set Low Level pattern

Figure 9. Controller Configured pattern

Figure 10. Operating Mode pattern

Summary of Contents for Dazzle












