background image

17

18

To Enter the Type Select Mode

Press the DOWN and SELECT keys simultaneously, then turn on the transmitter.

Press the UP key until the TYPE SELECT appears on the screen.

To Select a Model Type

Press the INCREASE or DECREASE key to witch between the heli or acro

 model type.

press the CLEAR key to accept the new model type . All settings will be 

set to the factory defaults if the selected memory group is previously used 

type label 

Model Reset and Integrated Timer Reset

The Model Reset function allows the model memory of the current model to be

reset to the factory default setting. This screen also allows the integrated timer to 

be reset.

To Perform a DATA RESET or Reset the Integrated Timer

Press the DOWN and SELECT keys simultaneously, then turn on the transmitter.

.

Enhanced wireless Trainer

The T7AH-2400 offers a Wireless Trainer Function. Premise is the transmitter's and

 transmitter's sets are the same

To Enter the Trainer Mode:

Press the DOWN and SELECT keys simultaneously, then turn on the transmitter.

Press the UP key until TRAINER function appears on screen.

Press the INCREASE or DECREASE key to activate or close Trainer function, then 

TRAINER TRIM only used as a traniner switches.

Throttle Recovery

The T7AH-2400 has a unique throttle trim recovery feature. Throttle Recovery 

stores the last known throttle trim position once throttle restore function is activated.

 That stored position is then recalled by moving the throttle trim up (open) one notch 

when the throttle trim is moved to the full down (closed) position. This makes shutting 

off the engine and restarting it with the correct trim position easy.

To Activate the Throttle Recovery Function

Press the DOWN and SELECT keys simultaneously, then turn on the transmitter.

Press the UP key until THRO RECOVERY appears on screen.

Press the INCREASE or DECREASE key to turn on/off the Throttle Recovery function.

[

TYPE

  

SELECT

]

MODEL

   

1

HELI

INCREASE and DECREASE key

Hold

 

while

 

turning on

  

transmitter

ACRO

Accept

 

new

 

model

 

type

YES

     

CLEAR

 

KEY

[

MODEL

  

RESET

]

MODEL

   

1

    

ACRO

     

DATA

  

R

ESET

INTEG

-

T

Press

 

to

 

enter MODEL

 

RESET

Hold

 

while

 

turning

on

 

transmitter

Press

 

to

 

select

RESET

 

or

 

INTEG

-

T

Press

 

to

 

reset

data

 

or

 

timer

0

:

00

:

34

INCREASE

 

and

 

DECREASE

 

key

Press

 

to

 

select MODEL

 

SELECT

Press

 

to

 

enter

function

 

main

 

screen

Press

 

to

 

enter

COPY

 

screen

Press

 

to

 

copy

selected

 

model

INH

 [

TRAINER

 ]

Press the UP or DOWN key until MODEL RESET appears on the screen.

Use the SELECT key to select DATA RESET or INTE-T.

When DATA RESET is selected, pressing the CLEAR key will reset the date to the 

factory default setting for that model, or if INTE-T is selected, the integrated timer

 will be reset to 0:00:00

Pole mode

The T7AH-2400 have in four different control rod "mode" (0, 1, 2, 3). Different mode 

corresponding to operation function of different control rod. Usually, set in "mode" 1.

Summary of Contents for T7AH-2400



































Reviews: