background image

5

SMART SYSTEMS FOR ACCESS CONTROL

Thank you for purchasing the Zareba Automatic Gate 
Opener. 

Your Zareba Automatic Gate Opener is designed for 
years of trouble free performance. It will provide you 
with a comfortable, safe, hassle-free way to access your 
property.

The Zareba Automatic Gate Opener is designed to work 
on single or dual swing gates. Each individual gate can 
be up to 18 feet long and weigh up to 850 pounds. 
Your gate opener will work on a variety of gate types 
such as iron, tubular, chain link, vinyl, etc. It is not rec-
ommended to use an automatic gate opener on a solid 
fence due to wind resistance. Depending on the 
strength of the wind and the obstruction sensing, your 
gate may not operate properly.

Your Zareba Automatic Gate Opener can be opened 
and closed in a variety of ways. Primarily, you will use 
your remote transmitter (included with your unit) to 
open or close the gate. However, the gate can also be 
opened with a hardwired button, an automatic vehicle 
sensor, a keypad, or built-in vehicle transmitter systems. 
These accessories are discussed later in this manual. The 
gate can also be closed with the hardwired button or 
keypad. In addition it can be closed automatically using 
a time delay that is set in the control box.

Your Zareba Automatic Gate Opener is designed to pro-
vide for safe operation. One of the most important fea-
tures of your gate opener is obstruction sensing. Your 
gate opener includes an adjustment for setting the sen-
sitivity of the obstruction performance. When there is an 
obstruction that prevents the gate from opening or 
closing, the gate will immediately stop and reverse 
direction. If the obstruction is removed the gate may be 
activated to continue its path from where it stopped. If 
the obstruction is not removed, the gate opener will 
sound an alarm and will not operate again until the 
gate opener system is reset. 

There are a number of accessories that can be installed 
with your gate opener that maximize your benefit to 
owning the system. The accessories include additional 
transmitters, keypad, pin lock, solar panel, in-ground 
vehicle sensor, and others. Please see the 

List of 

Accessories

 at end of this manual.

You may obtain additional copies of this manual from 
our web site at www.zarebasystems.com, or contact 
Zareba Systems at: 906 5th Ave. E, Ellendale, MN 
56026, 1-800-272-9877.

AN INTRODUCTION TO 
AUTOMATIC GATE  
OPENERS

Summary of Contents for G550










































Reviews: