Zapak ZP-SW25 User Manual Download Page 5

 

REMARKS

 

1.

 

Each  tool  is  equipped  with  one  ZAPAK  battery  powered  plastic  sealing  tool,  one 
BOSCH  Li-Ion  battery,  one  BOSCH  charger(with  charger  manual),  cleaning  brush, 
bottom  sealing  gripper  plate,  strap  width  adjustment  set  and  operation  user  manual 
etc.   

2.

 

All  electrical  and  mechanical  specifications  conform  to  the  most  major  safety 
standards.    Please refer to the label and packaging for detail information. 

3.

 

Plug specification of charger varies with different country /areas’ request. 

4.

 

Most parts of this tool are made  of recyclable material.    Please refer to the recycle 
mark on each component. 

5.

 

Products and specifications subject to change without notice. 

 

3. SAFETY INSTRUCTION 

When using this sealing tool, basic safety precautions should always be followed to 

reduce the risk of fire, leaking batteries and personal injury including but not limited to 

the followings:   

Read all these instructions before operating this product and save these instructions. 

 

 

Number of sealing cycles varies based on strap quality, 

specification, set sealing time, operation habit, ambient environment 
(The approx. number was tested on normal quality straps based on 
a new and fully charged Li-Ion battery, part no. 9380 ).

 

 

3.

 

Life  cycle:  Approx.  2000  charges 

(based  on  proper  charging  & 

discharging operation and working habits).

 

 

4.

 

Please refer to “4.3. Charging Battery“ regarding usage and 
storage of battery 

 

5.

 

Storage temperature : -20

~60

 (-20

~20

 would be better)   

 

Storage humidity:      65% ± 20%   

6. 

  Ambient temperature: -10

~40

   

7. 

  Average  ambient  temperature  for  charge  is  0 

0

C~45 

0

C,  charging 

efficiency drops if ambient temperature is  above 45 

0

C or lower than 0 

0

C  which  may  lead  to  deterioration  in  performance  and  even  battery 

leakage. 

(Please refer to article 3. “SAFETY INSTRUCTION “ and BOSCH 
Safety Notes regarding environmental, recycle and safety 
precautions of battery.) BOSCH Li-Ion battery (No. 9380) complies 
with UN38.3 safety requirements.

 

H.

 Bosch 

Charger

 

For ZP-SW25 ( ZAPAK part no.2382-XX, BOSCH Charger no. 
AL1860CV/GAL1880CV): Charging time 30 minutes under normal 
condition.

 (Please refer to user manual of Bosch charger for detailed 

specification and safety precautions.)

 

 

 

Summary of Contents for ZP-SW25






















Reviews: