background image

15

GB

INSTALLATION

Wall drilling and bracket fixing

Wall marking:
• Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of 

the area in which the hood will be installed.

• Draw a horizontal line at: 

955 mm above the hob for installation without the back panel, 
a 955mm above the surface on which the pack panel rests

,

 for installation with the back panel.

• Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the 

centre (notch) with the vertical reference line.

• Mark the wall at the centres of the holes in the bracket.

Place bracket 

7.2.1

 on the wall as shown at X mm below the first bracket (

= height of the upper 

chimney section supplied), aligning the centre (notch) with the vertical line

.

• Mark the wall at the centres of the holes in the bracket.
• Mark a reference point on the horizontal reference line as indicated, 116 mm from the vertical 

reference line.

• Repeat this operation on the other side.
• Drill ø 8 mm holes at all the centre points marked.
• Insert the wall plugs 11 in the holes.
• Fix the brackets using the 12a (4,2 x 44,4) screws supplied.
• Insert the two screws 12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap of 5-6 

mm between the wall and the head of the screw.

955

X

116

1÷2

116

955 min.

7.2.1

11

12a

Summary of Contents for ZHC 927













Reviews: