Zanussi ZHC 927 Page 11 Installation, Use And Maintenance Handbook Download | Manualshive

Page: 11 / 12

background image

21

GB

Lighting

LIGHT REPLACEMENT

• 20 W halogen light.
• Remove the 2 Screws fixing the Lighting

support, and pull it out of from the Hood.

• Extract the Lamp from the Support.
• Replace with another of the same type, making

sure that the two pins are properly inserted in
the lamp holder socket holes.

• Replace the Support, fixing it in place with the

two Screws removed as above.

«
...
9
10
11
12
»

Summary of Contents for ZHC 927













Reviews:

No comments

Related manuals for ZHC 927

Brand: Kuppersbusch Pages: 17

Brand: Omega Pages: 12

Brand: V-ZUG Pages: 6

Brand: Everdure Pages: 9

Brand: Jenn-Air Pages: 40

Milano Island ZML-M90AG

Brand: Zephyr Pages: 21

Brand: Omega National Pages: 16

Brand: NEFF Pages: 72

Brand: Swegon Pages: 60

Plane Black Isola 90

Brand: FALMEC Pages: 59

Brand: CIARRA Pages: 24

Brand: eisinger Pages: 52

Brand: Smeg Pages: 14

Brand: Smeg Pages: 153

Brand: FALMEC Pages: 28

Brand: Candy Pages: 20

Brand: Candy Pages: 36

Brand: Gorenje Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands