Zanussi ZBHC8 User Manual And Installation Instruction Download Page 7 | Manualshive

Page: 7 / 16

background image

Delay

Vent Function

15 minutes

-06-

Installation of Remote Controller

This is the wireless remote control, please install it to the suitable place with the accessory

holder if necessary

1.Fix the R/C holder to the designated place and make marks according to the arrows

2.Dig holes 1/4(6mm) according to the marks, and fill in the holes with 4 plastic plugs.

3.Put the remote controller into the holder.

«
...
5
6
7
8
9
...
»

Summary of Contents for ZBHC8

















Reviews:

No comments

Related manuals for ZBHC8

WhisperGreen FV-08VKM2

Brand: Panasonic Pages: 16

Brand: ebm-papst Pages: 11

Brand: ELTA FANS Pages: 16

Brand: WAFE Pages: 16

AirPro Willacy P250063

Brand: Progress Lighting Pages: 51

ComfoAir Compact CA155WM

Brand: Zehnder Rittling Pages: 20

SPITFIRE MA6721B Series

Brand: Fanimation Pages: 40

Brand: Mistral Pages: 5

Brand: Kichler Lighting Pages: 60

Brand: Metal Fab Pages: 2

Brand: Fanco Pages: 8

Brand: ebm-papst Pages: 12

Brand: Harbor Breeze Pages: 14

Brand: Vortice Pages: 80

Brand: Yoer Pages: 24

Brand: Casa Fan Pages: 40

Brand: Sulion Pages: 20

Brand: Omega Altise Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands