background image

7

MAINTENANCE AND CLEANING

INSTRUCTIONS FOR THE INSTALLER

ATTENTION: This appliance must be installed and used only in rooms which are permanently

ventilated according to the regulations in force.

The following instructions relating to installation and regulation must be carried out by qualified
personnel.  The appliance must be installed correctly in conformity with the rules and regulations in
force. All interventions must be carried out with the appliance electrically disconnected.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR ANY DAMAGES

DERIVING FROM AN INSTALLATION WHICH DOES NOT CONFORM WITH THE

REGULATIONS IN FORCE.

SITE OF INSTALLATION

For a good operation of the gas appliance it is
indispensable that the air necessary for gas
combustion can circulate in the room in a natural
manner. (The installer must follow the regulations
in force.)

Before each operation electrically disconnect the
appliance.
Wash the enamelled parts with warm water and
detergent, do not use abrasive products which
could damage them;  frequently wash the baffles
of the burners with boiling water and detergent,
taking care to remove all encrustrations;  the parts
in stainless steel should be rinsed well with water
after use and dried with a soft cloth.
The hob’s enamelled grills can also be washed in
the dishwasher. For persistent marks use normal,
non-abrasive detergents or specific products
which can easily be found in commerce.

It is never advisable to use wire pads, steel wool
or acids for cleaning.

For hobs having automatic ignition periodically
carry out an accurate cleaning of the ignitor
(ceramic or electrode) to avoid ignition
difficulties, furthermore check that the baffle
holes are not obstructed.

Clean the plates with a damp cloth and lightly
grease with vegetable oil or sewing machine oil
whilst still warm.

Periodic oiling of the taps must be carried
out by qualified personnel who should also
be contacted if a fault in the functioning of
the appliance occurs.

The appliance must be installed at a
minimum distance of 50 cm. from curtains
or other combustible material.

Summary of Contents for Hobs















Reviews: