Z3 Technology Z3-DME-10 User Instructions Download Page 53

Page: 53 / 60

DOC-USR-0096-06

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

Dest Address

(ZIXI Only)

Sets desintation of Zixi Feeder

stream.

Should be formatted as: “address:port/streamid”

Zixi Auth Enable

(ZIXI Only)

True

False

Selecting “True” allows for entering valid Zixi user
credentials.

User ID (ZIXI Only)

Allows for entering valid Zixi user ID.

Zixi Overhead

(ZIXI Only)

1-100

Adjust Zixi percent overhead.

KLV Enable

True

False

Enables the capture and insertion of KLV data into
the bitstream.

KLV Pid

0-8191 (

)

PID assigned to the KLV stream in the TS stream

KLV Bitrate

100 – 1M

Expected bit rate of the KLV stream.

KLV Mode

SDI

FILE

Sets the source type for the KLV stream currently
only and SDI source or a binary file containing KLV
data are the only valid sources.

KLV Source

/dev/gv7601.0

Location of KLV source this will be a character
device for SDI Mode and or a file for FILE Mode.

Channel Controls

Stop Button

Stop current encode session for Channel 1. Encode
must be stopped in order for settings to be altered.

Start Button

Start encode session for Channel 1.

Delete Button

Removes channel instance for encoding.

status

!Not running, IDLE,
STOPPED, RUNNING,
POLLING

Current status of the encode process.

IDLE

indicates no valid input data is present.

STOPPED

indicates that the unit is not currently

encoding. Must be in this mode to make any
configuration changes.

POLLING

indicates “start” was pressed and the

encoder is waiting for valid input data to be
detected.

RUNNING

indicates the unit is currently encoding.

Error statuses will be preceded by an exclamation
point and include a description of the error.

Summary of Contents for Z3-DME-10





























































Search results

Summary of Contents for Z3-DME-10

Reviews:

Related manuals for Z3-DME-10

Brands by name

Popular brands

Z3 Technology Z3-DME-10, User Instructions

Search results

Summary of Contents for Z3-DME-10

Reviews:

Related manuals for Z3-DME-10

Brands by name

Popular brands