Z3 Technology Z3-DME-03 User Instructions Download Page 33 | Manualshive

Page: 33 / 54

background image

DOC-USR-0061-03

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

33

7.0

STREAMING RTMP IN THREE DIFFERENT RESOLUTIONS

This section shows how to use the Z3-DME-03 to take 1 video input and stream it over RTMP into 3 different
resolutions (720p, D1, and CIF). The Wowza server is used as an example RTMP server to stream to.

These instructions can also be used to determine how to stream the same input into multiple
configurations. Simply specify “RTP”, “UDP”, or “TSFILE” instead of “RTMP”, and ignore the sections
referring to Wowza in this section. Note that, if multiple channels off the same input is done, the total
performance cannot exceed the capability of the Z3-DME-03 (for example, 3 1080p30 encodes at 30fps
would not be allowed).

7.1

Connect the Encoder

Follow steps (1) to (11) in Section 6.0 to connect the Z3-DME-03 for encode and bring up the

Encoder GUI.

7.2

Configure the Encoder for “Multiple Output from One Input” Mode

At the Configuration Option portion towards the bottom, select “Encode 1 to 3 Ch”:

Two channels appear. To create a third channel, click on the “+” to the right of the CH2 tab:

Click on “+” to create
CH3

Figure 40 Changing to “Encode 1 to 3 Ch” Mode

Change here to
“Encode 1 to 3 Ch” Mode

Figure 41 Creating CH3

«
...
31
32
33
34
35
...
»

Summary of Contents for Z3-DME-03























































Reviews:

No comments

Related manuals for Z3-DME-03

Brand: Samson Pages: 28

Brand: National Instruments Pages: 10

Atlona Omega AT-OME-SR21

Brand: Panduit Pages: 28

Brand: Wyrestorm Pages: 4

Brand: Lumin Pages: 11

Brand: Future Illuminations Pages: 2

Brand: Baja Silueta Pages: 99

Brand: Delta Electronics Pages: 2

CONSONANCE REFERENCE DB1

Brand: Opera Pages: 3

INTERNATIONAL TRAVEL ADAPTER

Brand: Igo Pages: 1

Brand: Milexia Pages: 17

Brand: RGBlink Pages: 46

Brand: MPP Solar Pages: 4

Brand: Intech Pages: 4

Atlona OmniStream 122

Brand: Panduit Pages: 12

Brand: Jaguar King Pages: 54

Brand: DANE-ELEC Pages: 2

Brand: Tektronix Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands